Chevrolet GMC Fuel Pump & Sending Unit Assembly TRQ

Our electrical and electronic parts are subject to strict quality testing.

Parts cannot be returned after they have been installed. Contact us with any questions before installing the parts.

This fuel pump includes a new electrical connector harness. You will need to remove your existing electrical connector and install the new connector provided in order to install your new fuel pump (instructions are included with the pump).

This fuel pump is not a universal fit item. Because your vehicle’s original connector is prone to failure due to corrosion, cracking, loose pin housings, and wire crimp issues, the OE manufacturer has changed the shape of the connector, requiring the install of a new electrical connector during fuel pump service.

Meets or exceeds all SAE fuel pump performance and durability standards

Consistent high quality plastic molding media.

High-carbon motor commutator and brushes for longer pump life

Guaranteed to fit and function correctly for your specific application

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

step : Disconnecting the Fuel Hoses (0:41)

• Lift and secure the vehicle
• Loosen the two hose clamps with an 8mm socket and ratchet
• Pull the hoses free, using a pry bar if necessary

step : Removing the Fuel Tank Straps (1:41)

• Support the fuel tank with a jack stand
• Remove the 15mm bolt from each fuel tank strap
• Pull off the fuel tank straps

step : Removing the Fuel Tank (2:39)

• Have an assistant hold one end of the tank
• Lower the jack
• Pull the top hose free from its bracket
• Disconnect the rear hose from the fuel tank
• Disconnect the rear hose from its brackets
• Disconnect the fuel pump wiring harnesses
• Disconnect the fuel pump hoses with pliers
• Pull the front hoses out of the gas tank
• Pull the fuel pump hoses out of their brackets
• Tape over the holes in the fuel tank
• Lower the fuel tank with the help of an assistant
• Disconnect the top hose from the fuel tank
• If the gas tank is too heavy, pour the gas into an appropriate container

step : Removing the Fuel Pump (5:25)

• Loosen the fuel pump ring with a hammer and screwdriver
• Pull of the fuel pump ring
• Pull the fuel pump out of the tank
• Pour any gas inside the pump into the tank

step : Installing the New Fuel Pump (6:12)

• Push the float arm onto the new fuel pump
• Slide the fuel pump hose clips off the old fuel pump with a flat blade screwdriver
• Slide the fuel pump hose clips onto the new fuel pump with a flat blade screwdriver
• Put the new fuel pump into the tank
• Put the fuel pump ring into place
• Lock the ring into place with a hammer and screwdriver

step : Reinstalling the Fuel Tank (7:14)

• Lift the fuel tank into place, front first, with the help of an assistant
• Reconnect the front fuel tank hose
• Clip the front hose into its bracket
• Push the rear of the tank up partially
• Support the tank with the jack
• Connect the fuel pump hoses
• Reconnect the fuel pump wiring harnesses
• Clip the fuel pump hoses into their brackets
• Connect the rear hose
• Push the rear hose into its brackets
• Raise the tank the rest of the way up with the jack
• Remove the tape from the tank
• Reconnect the two upper hoses
• Tighten the two hose clamps with an 8mm socket and ratchet

step : Installing the New Fuel Tank Straps (11:05)

• Hang the new fuel tank straps in their brackets
• Insert the 15mm bolt into each fuel tank strap