Replaces

Cadillac CTS CTS-V Steering & Suspension Kit - 1ASFK05379

Part Details

  • Quantity: 10 Piece Set
  • Kit Includes:
    (2) Front Sway Bar Links
    (2) Rear Sway Bar Links
    (2) Front Lower Control Arms with Ball Joints
    (2) Front Outer Tie Rods
    (2) Front Inner Tie Rods

 

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

WARNING:  This product can expose you to chemicals including Carbon black, which is known to the State of California to cause cancer.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

    Regarding alignments, it's suggested that you have an alignment performed after you do a replacement like this.

  1. step : Testing the Tie Rod (0:15)
    • Jack up one of your front wheels
    • Grab it by the sides of the tire and try to move it back and forth. If you feel more play than just the steering rack moving back and forth, then your tie rod probably needs replacing
  2. step : Removing the Front Wheel (0:56)
    • If you don't have air tools, you'll want to loosen the lug nuts with the wheel on the ground
    • Lift the vehicle with a jack, support it with a jack stand, and take the wheel off the rest of the way
  3. step : Measuring the Tie Rod (1:19)
    • Before you disassemble the tie rod, you want to measure the tie rod
    • From a fixed point on the rack, like the end of the boot, you want to measure to the middle of the tie rod
    • Measure a few times to be sure-you're going to set the new tie rod up the same length
  4. step : Removing the Tie Rod (1:58)
    • You'll see a lock nut at the end of the tie rod. Holding on to the tie rod with a wrench, use your adjustable wrench to loosen that nut about a quarter of a turn
    • There is also am 18 mm bolt that nut that holds the stud on. Remove that
    • Separate the tie rod from the steering knuckle by using a tie rod fork. Taking a hammer, you'll drive the tie rod fork between the rod and the knuckle
    • Once the tie rod is separated from the knuckle, turn it clockwise to get it off the steering rack
  5. step : Replacing the Tie Rod (3:45)
    • The new tie rod should come with the bolt in it. Take the bolt out for now.
    • Thread the tie rod onto the nut, measure from the same fixed point as before and make sure it measures the same. Take a couple of measurement.
    • Also, make sure you do not twist the shaft that comes out of the steering rack. Doing so will change your alignment.
  6. step : Securing the New Tie Rod (4:39)
    • Once you have the measurement correct, then you can put the tie rod back into the steering knuckle and start the bolt on there
    • The lock nut at the end of the tie rod is an 18 mm nut. Holding the stud of the tie rod with an 8 mm wrench, tighten up the nut with your 18 mm wrench
    • Once the 18 mm wrench is tight, grab another wrench and hook it on there for leverage. Give it another pull just for good measure
    • Torque it to 65 foot pounds
    • Put your wrench onto the inner tie rod to get this locking nut back out against the outer tie rod. Tighten
  7. step : Replacing the Wheel (5:53)
    • Turn the wheels straight, and put your wheel and tire back on
    • Start the lug nuts by hand at first to primarily tighten them.
    • Lower the car back onto the ground
    • Set your torque wrench to 90 - 95 foot pounds and tighten your lug nuts in a star pattern

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Torque Wrench

  • Sockets - Metric

  • 18mm Socket
  • 19mm Socket

  • Specialty Tools

  • Tie Rod Fork

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2003-2007Cadillac CTS Cadillac CTS 10 Piece Set Steering & Suspension Kit
2004-2007Cadillac CTS-V Cadillac CTS-V 10 Piece Set Steering & Suspension Kit

This part replaces:

  • Moog EV800332
  • Moog K80564
  • Moog K750020
  • Moog K750016
  • Hollander 512-01329L
  • Hollander 512-01328R
  • Hollander 512-01330R
  • Hollander 512-01331L
  • Dorman 521-019
  • Dorman 521-020
  • Moog ES3585
  • Moog ES3586
  • OE # 25758280
  • OE # 25758282
  • OE # 25758281
  • OE # 25758283
  • OE # 25740375
  • OE # 15859812
  • OE # 88892774
  • OE # 88892776
  • OE # 88892773
  • OE # 15858711
Only 2 left in stock
Part #: 1ASFK05379


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(06:35 min)