This combination cruise control, wiper, high beam and turn signal switch lever is a new, aftermarket replacement part. It is designed to REPLACE original units that are prone to failure. It's just what you need to get your vehicle in good working order again!

Specifications:

  • Replaces dealer part numbers: 88963625, 26049071, 26067715, 26081121, 26085929
  • Direct replacement
  • Design improved for more durability
  • Detailed graphics
  • Built to strict quality control standards
  • For models with cruise control

This combination lever is designed to replace your original with no modifications necessary.

 

Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

 

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

4.9 / 5.0
24 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
22
1
1
0
0
Great part
Part went on just as it was supposed to. Perfect fit. I would highly recommend this
May 15, 2018
Purchased
2 months ago
Perfect fit, works well, great price
I replaced the switch in my daughter's 2005 Century because the headlights would intermittently go out and the car would occasionally accelerate on its own. Both problems were traced to an issue with this switch (the dimmer and cruise acceleration controls). We've had no issues since. Installation took longer than expected (about 2 1/2 hours), but that was because I was being very careful to not damage any of the interior trim pieces and spent quite a bit of time watching online videos for tips. If I was to do it again, I'm sure I could get it done in 30-45 minutes. Hopefully, the following tips will save the next person some time. I also recommend searching for the online videos, because it helps to watch another person do it.

1. Take the time to remove all of the dash trim, including the felt trim below the driver's side dash, the panel covering the heater controls, the side panels by both door posts, the panel below the steering column, the panel to the right of the glove box and the long piece covering the instrument cluster and radio and that runs above the glove box. There are push clips attaching the felt trim, and 7mm screws at the bottom of the other panels. There is also a 7mm screw under the passenger-side side trim panel (where the fuses are). Otherwise, everything is held in place with snap clips.

2. To remove the bottom half of the steering column trim, remove the two T-25 screws from the bottom. Next remove the tilt lever by gently wiggling it back and forth and up and down while pulling. It snaps in and out without any hardware attaching it. Then gently unsnap the bottom of the trim from the top piece by using your thumbs to flex the seam where they meet. Where the trim meets the steering wheel, you can push it toward the dash to get it to clear the wheel. Try to loosen the end toward the wheel first and then hinge it down to release the end closest to the dash. You will see hinge-like clips that hold the top and bottom together on the dash end.

3. To remove the top trim from the steering column, there is a hidden fastener behind the right side of the steering wheel. From underneath, shine a light up right behind the steering wheel. You will see a small black fastener that looks somewhat like the end of a hex key. Use a 4mm socket on an extension to reach and remove it. Then, with the gear shift all the way down, gently work the trim off the column. Loosen the left side first, then slide it past the ignition.

4. To remove the wire harness from the under dash block into which it is plugged, use a 7mm socket to unscrew the bold in the center of the block. Unplug the block. The two ends of the wire harness slide out of the block, but they are secured by a small plastic tab. Slide the tip of a screwdriver between the connector and the body of the wire block and slide the connector in the direction of the wires. Twist the screwdriver very slightly to allow the connector to clear the plastic tab.

5. The turn signal assembly is attached to the steering column with two T25 screws. One is on the top and easy to access. The other is behind the steering wheel and can be difficult to reach. To remove it, get a T25 drive bit with a 1/4" shank. Put the bit into the head of the screw and then use a small crescent wrench to turn the bit and loosen the screw until you can remove it with your fingers.
April 22, 2018
Purchased
3 months ago
turn signal switch
Friend of mine installed switch on 1/27/18 in 2 hours.Everything went fine and seems to work fine.Only thing i noticed was the light panel with the letters park,r,d,3,2, and l were not as bright and easy to see as before installation.
January 28, 2018
Purchased
6 months ago
Multi-function switch lever replacement
The multi-function switch on my 1999 Buick was not operating completely, as the bright headlights would not say on so my car would not pass the annual State Inspection certification. 1A Auto had the part at a great price and shipping was free. Awesome.
January 25, 2018
Perfect
I bought this part online hoping it would fit, and I was pleasantly surprised that when I installed it it was perfect. I watch YouTube videos online and follow their instructions and had it installed in two hours. If I need more parts for my older Buick, I would definitely buy them from 1aauto.com
December 20, 2017
Purchased
7 months ago
Buick Century leverr control switch
Switch is installed and working as it should. Onlyy been installed 4 days .
December 5, 2017
Purchased
8 months ago
Now comes the difficult part - installation!
The part came in record time, now I just have to get up the nerve to watch all the installation videos and make sure I know what to do. Always a learning curve but sure a ton cheaper than getting it done by someone else. The helpful videos are the key! Keep them coming.
December 5, 2017
Purchased
8 months ago
Works Great
I am pleased that I bought from you guy's. Not only for the price, but the warranty, product support, and quality. Thank You so much.
December 3, 2017
Purchased
8 months ago
Works great!
Arrived in a few days and works and installed with no issues, just like the original part.
September 17, 2017
Purchased
10 months ago
High Beam switch for Century Buick
Received the part and was pleased. It was installed yesterday and it is working great. Glad I ordered it from 1A Auto! Appreciate all the support and shipment. Thanks!
September 7, 2017
Purchased
11 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1997-2005 Buick Century Combination Switch for Models with Cruise Control
  • 1997-2004 Buick Regal Combination Switch for Models with Cruise Control

This part replaces:

  • Hollander 629-00148
  • OE # 88963625
  • Standard Motor Products DS-721
Part #: 1AZCC00165

How-to Video:

(00:50 sec)