100% CNC-Machined to Exact OE Specs

100% CNC-Machined to exact OE specs and balanced to reduce vibration

Cast from OE Grade Alloy

Manufactured from OE Grade G3000 Casting Alloy

Non-Directional Surface Finish

Non-Directional Rotor Surface Finish helps ensure smoother, quieter, and more effective braking

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:57)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Inspecting the Brakes (1:15)
    • Turn the rotor by hand or turn the steering wheel to turn the rotor
    • Check the thickness of the brake pads
    • Check the brake pad wear indicators
    • Check for gouges on both sides of the rotor
  3. step : Removing the Brake Pads (2:02)
    • Remove the two 14mm bolts from the brake caliper
    • Pry the caliper off with a flat blade screwdriver
    • Pull the caliper aside
    • Pull the brake pads off
  4. step : Removing the Brake Rotor (2:40)
    • Check that the caliper slides move freely
    • If the slides do not move freely, apply penetrating oil
    • Twist the slide out with water pump pliers and a hammer
    • Twist the slide out with a pair of vise-grip pliers
    • Remove the two 19mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Pull the rotor off
  5. step : Installing the New Brake Rotor (4:29)
    • Slide the rotor on
    • Thread one lug nut by hand to hold the rotor in place
    • Put the bracket back into place
    • Start the two 19mm bolts by hand
    • Tighten the bolts to 100 foot-pounds of torque
    • Clean the caliper slides with a wire brush
    • Apply penetrating oil to the slides
    • Apply bearing grease to the slides
    • Insert the caliper slides
  6. step : Installing the New Brake Pads (5:41)
    • Use a large C-clamp to push the pistons back into the caliper
    • Install the new brake pads into the bracket with the wear indicator tab on the upper side
    • Put the caliper on
    • Thread the two 14mm bolts by hand
    • Tighten the two 14mm bolts to 20 foot-pounds
    • Pull the wheel straight
    • Remove the place holder lug nut
  7. step : Reattaching the Wheel (7:43)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 100 - 110 foot-pounds in a crossing or star pattern
  8. step : Testing the Brakes (8:16)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Hammer
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Bearing Grease
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers
  • Slip-Joint Pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet
  • A Piece of Pipe (for leverage)
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 21mm Socket
  • 14mm Socket
  • 19mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1999-2002 Infiniti G20 Front & Rear Brake Rotor
  • 1993-2001 Nissan Altima Front & Rear Brake Rotor
  • 2000-2001 Nissan Sentra L4 2.0L Front & Rear Brake Rotor
  • 2002-2003 Nissan Sentra L4 2.5L Front & Rear Brake Rotor
  • 2004-2006 Nissan Sentra L4 2.5L Front & Rear Brake Rotor for Models without Brembo Calipers

This part replaces:

  • Reference Number 31057
  • Reference Number 34046
  • Hollander 530-58790
  • Hollander 533-58230, 533-58516
  • OE # 40206-7J101
Part #: 1ABFS03204


How-to Video:

(08:45 min)