This front wheel bearing/hub assembly, brake rotor, & brake pad set is just what you need to get your vehicle in good stopping order again!

Brake Pad Specifications:

  • 4 Piece FRONT Brake Pad Set
  • No core charge
  • Direct replacement
  • Professional Grade Ceramic Enhanced Disc Brake Pads

Brake Rotor Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • No core charges
  • Direct replacements
  • Fit 6 Lug Wheels

Wheel Bearing & Hub Assembly Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • 3 Bolt Flanges
  • Fit 6 Lug Wheels
  • Replaces dealer part numbers: 15997071, 15997072
  • Have ABS sensors
  • Studs already installed
  • Direct replacements
  • Built to strict quality control standards
  • Fit 4WD (4 Wheel Drive) Models only

This wheel bearing/hub assembly, brake rotor, & brake pad set makes great replacements and has good value over the price of dealer parts.

Positive Mold Technology

Positive Mold Technology improves durability and performance by allowing for even wear. High density, low resin friction material virtually eliminates brake fade and glazing, generates less brake dust, and promotes a longer-lasting , better performing brake pad.

OE Grade Multi-Layer Shim

OE Grade Multi-Layer Shim helps reduce vibration and noise

Environmentally Compliant

Certified Environmentally Compliant to "Better Brake Law" standards

Thermal Scorched

Pre-burnishing or "Thermal Scorching" is the final curing step in quality ceramic brake pad manufacturing. The brake pad's surface is heated to remove any uncured bonding agents and to stabilize the friction material to accelerate the break-in process and enhance stopping performance from the first stop.

100% CNC-Machined to Exact OE Specs

100% CNC-Machined to exact OE specs and balanced to reduce vibration

Cast from OE Grade Alloy

Manufactured from OE Grade G3000 Casting Alloy

Non-Directional Surface Finish

Non-Directional Rotor Surface Finish helps ensure smoother, quieter, and more effective braking

Precision Engineered

Precision Engineered using the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.

100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water, keeping grease clean for a longer bearing life.

Premium, heavy duty grease resists high temperature, moisture, and reduces intense friction pressure to help extend the life of the bearing.

Direct Fit Replacement

Direct fit replacement part is guaranteed to fit and function correctly for your specific application

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Remove wheel. (1:11)
    • Remove hub cap or center cap if you have it.
    • While your car is still on the ground, use your 22mm socket to loosen your lug nuts.
    • Jack up and secure your car with jack stands.
    • Remove the lug nuts with your 22mm socket and ratchet.
    • Remove the wheel and set aside.
  2. step : Remove the calipers (1:35)
    • Use a screwdriver to force the pistons back in.
    • Remove the two 3/8 Allen bolts to remove the calipers.
    • Use a wire tie to fasten the caliper out of the way.
    • Use your screwdriver to pry out your brake pads.
    • Remove the caliper bolt sleeves.
    • Check their condition and clean them with a wire brush if necessary.
    • Compress the caliper piston with a c-clamp.
    • Pull off the brake rotor.
    • Hit the rotor with a rubber mallet or hammer if necessary.
    • Take care not to damage the lug studs.
  3. step : Install new rotor and pads (7:15)
    • Clean new rotor with brake cleaner.
    • Insert your new pads into the brackets.
    • Put your caliper bracket back on, and tighten the 3/8 Allen bolts to 25-30 ft lbs.
  4. step : Put wheel back on (9:42)
    • Make sure to use a star pattern when putting your wheel lugs back on.
    • Tighten to 100-120 ft lbs.
    • Replace hubcap/center cap.
  5. step : Test and set brakes (10:08)
    • Before driving the car again, start it up and pump the brakes a few times to get the pistons in the brakes in place.
    • Test the brakes in your driveway before taking the car onto the road.
    • Set your rotors by evenly braking from 30mph to 10mph, 50mph-30mph and finally 70mph to 40mph.
    • This is best done on a straight back road without any traffic.

Tools needed for replacement:

    Allen Wrenches

  • 3/8 Inch Allen Wrench

  • General Tools

  • Floor Jack
  • Jack Stands
  • Large C-Clamp
  • Large Hammer
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Lug Wrench

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 22mm Socket

4.0 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
1
1
0
0
I thought this was very economical and would recommend your company to everyone. Got my merchandise faster than I thought.
January 22, 2018
Purchased
5 months ago
No bolts!
Wish it would have included the hub bolts from the get go.
January 17, 2018
Purchased
5 months ago
Smoking deal
Needed to replace the brakes and hubs on my 1997 silverado. Ordered this kit due to price. Whole kit was the price of 1 hub at the local auto parts store. Was impressed great quality. Will only buy parts from here.
March 5, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
Where is this product made?
Mike K on Aug 26, 2017
BEST ANSWER: These brakes are made in China.

Vehicle Fit

  • 1999 Cadillac Escalade 4 Wheel Drive Front Brake & Wheel Bearing Kit for Models with ABS Brakes Ceramic
  • 1995-1999 Chevy K1500 Truck Front Brake & Wheel Bearing Kit for Models with ABS Brakes Ceramic
  • 1995 Chevy K2500 Truck Front Brake & Wheel Bearing Kit for Models with 6 Lug Wheels with ABS Brakes & 11 Inch Rear Drums Ceramic
  • 1995-1999 Chevy Suburban K1500 4 Wheel Drive Front Brake & Wheel Bearing Kit for Models with ABS Brakes & 11 Inch Rear Drums Ceramic
  • 1995-1999 Chevy Tahoe 4 Wheel Drive Front Brake & Wheel Bearing Kit for Models with ABS Brakes Ceramic
  • 2000 Chevy Tahoe 4 Wheel Drive Front Brake & Wheel Bearing Kit V8 5.7L with ABS Brakes Ceramic
  • 1995-1999 GMC K1500 Truck Front Brake & Wheel Bearing Kit for Models with ABS Brakes Ceramic
  • 1995 GMC K2500 Truck Front Brake & Wheel Bearing Kit for Models with 6 Lug Wheels with ABS Brakes & 11 Inch Rear Drums Ceramic
  • 1995-1999 GMC Suburban K1500 Front Brake & Wheel Bearing Kit for Models with ABS Brakes & 11 Inch Rear Drums Ceramic
  • 1995-1999 GMC Yukon 4 Wheel Drive Front Brake & Wheel Bearing Kit for Models with ABS Brakes Ceramic
  • 2000 GMC Yukon 4 Wheel Drive Front Brake & Wheel Bearing Kit V8 5.7L with ABS Brakes Ceramic
Part #: 1ABMS00050


How-to Video:

(10:35 min)