Brake Pad Specifications:

  • Fits FRONT Rotors
  • 4 Piece Brake Pad Set
  • No core charge
  • Includes shims
  • Ceramic Enhanced Disc Brake Pads

Brake Rotor Specifications:

  • Comes as a PAIR
    • Fits both the LH (Driver Side) & RH (Passenger Side) FRONT
  • Replaces dealer part numbers: 8-15294-772-0, 8-21998-532-0, 8152947720, 8219985320, 25826102
  • Fits 6 Stud Wheels
  • 11.9" (302mm) Diameter

Wheel Bearing & Hub Assembly Specifications:

  • Comes as a PAIR
    • Fits both the LH (Driver Side) & RH (Passenger Side) FRONT
  • Replaces dealer part numbers: 12413037, 15130858
  • Includes lug nut studs already installed, ABS Sensors, and ABS Sensor Wire Harnesses
  • 3 Bolt Flanges
  • Built to strict quality control standards

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Step 1: Remove the wheel and tire (1:18)
    • Raise and secure the vehicle.
    • Remove the lug nuts and then the wheel.
  2. step : Step 2: Remove Caliper (2:07)
    • Turn wheels all the way in the opposite direction of the side you are working on.
    • Use your 13mm socket wrench to remove the caliper bolts.
    • Use a wire tie to help prevent stress on the caliper.
    • Use your 18mm socket to remove the brackets.
  3. step : Step 3: Remove brake disk (4:13)
    • Take care not to touch the disk, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
  4. step : Step 4: Remove Hub (4:42)
    • Use a 35mm socket to remove the hub nut.
    • Give the axle a slight tap with a hammer to loosen it.
    • Remove the 3 bolts securing the hub using your 18mm socket and extension and ratchet or breaker bar.
    • You can use penetrating oil to help.
    • Disconnect your ABS sensor.
    • Use a rubber mallet to break your hub free, and work around the flange with the hammer to pull it off.
    • Remove the hub and shield.
    • Clean up any corrosion with a wire brush.
  5. step : Step 5: Install new hub (9:10)
    • Use some penetrating oil to prep the knuckle for the new hub.
    • Put the three 18 mm bolts in place and tighten the nuts to 90 ft lbs.
    • Reinstall the ABS harness.
    • Tighten but don't torque the lug nut.
  6. step : Step 6: Put brakes and wheel back on (11:50)
    • Remember to replace the lug nuts on in a star pattern.
    • Lug nuts tighten to 100-120 ft lbs
    • Hub nut is 103 ft lbs.
    • Make sure to check your brakes and steering before driving again.
    • Make sure to pump the brakes and seat your rotors.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Large C-Clamp
  • Rubber Mallet
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Rust Penetrant
  • Wire Ties

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 18mm Socket
  • 19mm Socket
  • 35mm Socket

5.0 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
3
0
0
0
0
It was a great deal got the whole package cheaper than buying one bearing and rotor at my local parts store.shipping was fast and product was of good quality.very happy my first deal with 1a auto but I guarantee it won't be my last.
October 27, 2017
Purchased
4 months ago
Great Buy!
Great buy and value... the video you guys have done up make the install eady for this shade tree mechanic
October 27, 2017
Purchased
4 months ago
It was a good experience quality products and easy insulation and fast delivery
July 3, 2017
Purchased
8 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(13:45 min)

Tools List:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Large C-Clamp
  • Rubber Mallet
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Rust Penetrant
  • Wire Ties

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 18mm Socket
  • 19mm Socket
  • 35mm Socket




Vehicle Fit

  • 2006-2007 Buick Rainier Front Brake & Wheel Bearing Kit L6 4.2L without Sport Package
  • 2006-2009 Chevy Trailblazer Front Brake & Wheel Bearing Kit L6 4.2L
  • 2006-2009 GMC Envoy Front Brake & Wheel Bearing Kit L6 4.2L
  • 2007-2008 Isuzu Ascender Front Brake & Wheel Bearing Kit L6 4.2L
  • 2007-2009 Saab 9-7X Brake & Wheel Bearing Kit Front L6 4.2L
Part #: 1ABMS00013

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More