Specifications:

  • Brand New Suspension & Steering Kit
  • Comes as a Set of 10
  • Fits LH (Driver Side) & RH (Passenger Side) Front
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:46)
    • Remove the center cap with a cap removal tool or pick
    • Loosen the 17mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Simulating the Suspension (1:11)
    • Push up on the suspension with a floor jack until the suspension stops compressing
    • Measure the top of the strut mount and mark from the front of the tap to where it lines up at the bottom (3 1/4 inches)
    • Lower the floor jack to release the weight from the suspension
  3. step : Removing the Strut Assembly (2:19)
    • Remove the pinch bolt with a 16mm wrench and 16mm socket and ratchet
    • If the bolt won't remove, use a chisel and hammer
    • Slide a pickle fork under the joint
    • Hammer the pick fork in until it separates from the spindle
    • Remove the Phillips head screw from the coolant tank
    • Slide the tank out of its retainers
    • Remove the 16mm bolt below the expansion tank
    • Remove the rain tray
    • Pull off the rubber boot before the fuse box
    • Remove the 16mm bolt
    • Remove the 16mm bolt by the fuse panel
    • Remove the bolt from the bottom of the strut with a an 18mm socket and 18mm wrench
    • Remove the strut from the lower control arm
  4. step : Removing the Upper Control Arms (7:34)
    • Remove the 16mm bolts holding in the upper control arms
    • Remove the upper control arms
  5. step : Installing the Upper Control Arms (8:04)
    • Insert the upper control arm into place
    • Remember to transfer the mark you used to measure the angle of the control arms
    • Set the angle
    • Tighten the 16mm bolts
    • Torque the control arm bolts to 37 foot-pounds and add 90 degrees
    • Repeat the process for the other side
    • Remove the protective caps from the new boots
  6. step : Reinstalling the Strut Assembly (8:53)
    • Insert the strut assembly into place
    • Tighten the top strut bolts
    • Torque the strut bolts to 55 foot-pounds
    • If the strut rotates, twist it to it's in place
    • Tighten the lower strut bolt with an 18mm socket and wrench
    • Reinstall the forward control arm into the spindle
    • Press the control arm into the spindle with pliers
    • Insert the pinch bolt in halfway
    • Reinstall the nut on the back of the pinch bolt with a 15mm socket and wrench
    • Torque the pinch bolt to 30 foot-pounds
    • Torque the lower strut bolt to 66 foot-pounds
  7. step : Reattaching the Wheel (11:14)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 90 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Chisel
  • Hammer
  • Pick
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Channel-Lock Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 18mm Socket
  • 16mm Socket

  • Specialty Tools

  • Tie Rod Fork
  • Ball Joint Press
  • Audi Wheel Cap Removal Tool

  • Wrenches - Metric

  • 16mm Wrench
  • 18mm Wrench

2.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
0
0
0
1
0
Bad piece in kit.
I ordered a 10 piece Control arm kit for my suspension... One of the pieces had a ball joint that was bad and was only able to torque it to about 40 foot pounds before the whole thing started spinning and cannot get it tight. Honestly I'm pretty worried about my safety driving now.
September 5, 2017
Purchased
8 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2001-2003 Audi Allroad Steering & Suspension Kit 10 Piece Set
  • 2004 Audi Allroad Steering & Suspension Kit 10 Piece Set (Built Before 4/04 Production Date)

This part replaces:

  • Moog K622223
  • Moog K90497
  • Moog K90498
  • Moog EV440
  • Moog K80525
  • Moog K80526
  • Moog ES3646
  • Moog K622222
  • Beck Arnley 102-7549
  • Beck Arnley 102-7550
  • Reference Number MS101209
  • Dorman 520-763
  • Dorman 520-764
  • Dorman 520-767
  • Dorman 520-768
  • Dorman 524-471
  • Dorman 522-227
  • Dorman 522-228
  • Hollander 512-58738
  • Hollander 512-58575L
  • Hollander 512-58574R
  • Hollander 511-58167L
  • Hollander 511-58166R
  • Hollander 511-58126L
  • Hollander 511-58126R
  • OE # 4Z7407151C
  • OE # 4Z7407693D
  • OE # 4Z7407694D
  • OE # 8E0407505A
  • OE # 8E0407506A
  • OE # 8D0407509A, F, C, E, P
  • OE # 8D0407510A, F, C, E, P
  • OE # 4B0419811E, 4F0419811D
  • OE # 4D0422821A
Part #: 1ASFK03254

Out of Stock

How-to Video:

(12:37 min)