/1999 Buick LeSabre V6 3.8L 8th Vin Digit K 3 Piece Ignition Coil Set ACDelco ACERK00002
ACERK00002-3 Piece Ignition Coil Set ACDelco ACERK00002
ACERK00002ACDelcofalse
Replaces
1999 Buick LeSabre V6 3.8L 8th Vin Digit K 3 Piece Ignition Coil Set ACDelco ACERK00002
recommended installation videos
sponsored by
Out of Stock
$196.69
Notify When Available
recommended installation videos
sponsored by
Description
Vehicle Fit
Warranty & Shipping
How-To & Tools
Part Details
Quantity: 3 Piece
Kit Includes: (3) Ignition Coils
Specification
VIN Code
8th Vin Digit K
Engine Displacement (Metric)
V6 3.8L
Item Condition:New
1 Year Warranty
This item is backed by our 1-year warranty. In the event this item should fail during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How To Replace Ignition Coil 2000-05 Buick LeSabre
How To Replace Ignition Coil 1997-99 Buick Lesabre
Created on:
Tools used
Socket Extensions
Ratchet
7/32 Inch Socket
Marker / Writing Utensil
1. Removing the Ignition Coil
Twist the wires off the ignition coil
Remove the two 7/32" bolts from the ignition coil
Pull the ignition coil up and out
2. Installing the New Ignition Coil
Push the new ignition coil into place with the wiring connector facing the rear of the vehicle
Insert the two 7/32" bolts into the ignition coil
Twist the wires onto the ignition coil
Mark the ignition coil with its corresponding cylinder number
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to remove and replace the engine ignition coils on this 2000 Buick LeSabre, same as a 2000 to 2005 LeSabre, and pretty much the same as a lot of vehicles that have the 3800 Series V6. The only tool you'll need is a 7/32"? socket with a ratchet and extension.
The ignition coils on the 3800 V6 in this Buick LeSabre is very conveniently located right here on top. When one of these starts going bad, usually what it does is it will turn the check engine light on and it will say something like misfire in cylinder number 6 or 5 or 4 or something. That's generally a good indicator that your coil is starting to go bad. If that is the case, they're pretty easy to replace. You can see that the original coils are marked here with their cylinder numbers. We know that this plug is cylinder number 3. This wire goes to cylinder number 6.What you first want to do is get these plugs kind of a twist, and then pull off. Give this wire a little bit of a twist and then pull it up and off. Then, there's two 7/32"? bolts. Remove those. We'll just speed it up here as we remove those two bolts. Once you have those off, just pull the coil straight off.
Here's the new coil from 1AAuto. Right here, there are a couple of tabs or those are actually electrical connections and they go in right there. You want to carefully equip this right now. What you can do actually is put your screw in. Make sure that goes in and then put the coil down carefully onto those tabs. It basically plugs right in just like that. Then put another screw right down in.
We'll speed things up again here as we just put those two bolts in and tighten them up. Again, tighten them nice and firm. You don't want to over tighten them, though. This was the top plug wire and then the bottom plug wire. Because the replacement coil can fit anyone of these positions, they don't come marked with the serial numbers but you could take a crayon or some type of white paint marker and mark your cylinder numbers back on there using the old ones if you wanted to.
A suggestion would be if one of your coils goes bad, obviously at 1AAuto, we sell the coils so you can buy all three. I would also replace your plug wires and your spark plugs. That's kind of a way you do a basic tuneup on these newer engines is replacing the coils, plug wires, and spark plugs.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Ratchet
7/32 Inch Socket
1. Removing the Ignition Coil
Remove the two 7/32" bolts from the ignition coil
Disconnect the spark plug wires from the ignition coil
Pull the ignition coil up and out
2. Installing the Ignition Coil
Connect the spark plug wires to the ignition coil
Push the new ignition coil into place
Insert the two 7/32"bolts into the ignition coil
Repeat Steps 2 through 6 for the remaining coils
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video we're going to show you how to replace an ignition coil in a '97 Buick LeSabre. It's going to be the same operation for '97 through '99. You're going to need a 7/32"? inch socket and socket wrench and a new coil from 1A Auto.
The LeSabre has three ignition coils located on the top front of the engine. I'm using a 7/32"? socket and socket wrench to remove two screws that hold it in. As you remove the coil and take your spark plug wires off, just remember which one goes to the left post and which one goes to the right post.
Here you see the old part, and the new part from 1A Auto, which is identical, and will go in exactly the same way. Start by plugging in your wires. Seat it down, be careful not to bend these two connectors. Here I'm just re-installing those 7/32"? bolts. Just note that the procedure is the same for all three coils.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Product Reviews
Loading reviews
There are no reviews for this item.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Buick is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by Buick or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.