1ARFA00458-2010-17 Chevrolet Equinox GMC Terrain Radiator Dual Cooling Fan Assembly

Replaces

2010-17 Chevrolet Equinox GMC Terrain Radiator Dual Cooling Fan Assembly DIY Solutions

1ARFA00458
FREE SAME DAY SHIPPING
Save 32%
List: $389.95 Save: $125.00
Only 2 left in stock
Part 1ARFA00458
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

DIY Solutions
Brand #: HVA02300

Frequently bought together

Description
Vehicle Fit
Warranty & Shipping
How-To & Tools

Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a single purchase of a customized kit or set from DIY Solutions.

High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.

Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

Returns: Parts with electrical components cannot be returned once installed.

  1. step : Draining the Radiator (0:23)
    • Make sure the coolant is cool
    • Remove the overflow tank cap
    • Raise and support the vehicle if necessary
    • Place a drain pan below the radiator petcock, which is on the passenger side lower corner of the radiator
    • Open the radiator petcock
    • Allow the radiator to drain
  2. step : Removing the Bumper Cover and Headlights (2:12)
    • Remove the four push pin retainers from the driver side engine compartment trim
    • Remove the driver side engine compartment trim
    • Repeat for the passenger side
    • Remove the 10 mm headlight bolt that is recessed
    • Remove the two 7 mm bolts securing the headlight to the radiator support and the fender
    • Remove the four T20 screws along the top of the grille
    • Remove the four push pin retainers securing the driver side wheel well shield; two inner, and two along the fender
    • Remove the two T20 screws securing the driver side wheel well shield
    • Pull the wheel well shield away from the fender and bumper edge
    • Remove the inner 7 mm screw securing the driver side bumper cover to the fender
    • Twist counter clockwise to remove the fog light socket from the driver side light housing
    • Remove the two 7 mm screws securing the driver side wheel well shield to the underside of the bumper
    • Pull the wheel well shield away from the underside of the bumper
    • Repeat the driver side steps for the passenger side
    • Pull the bumper off, separating the clips along the underside of the headlight and fender
    • Remove the lower 7 mm headlight bolt that is behind the bumper cover
    • Disconnect the headlight assembly electrical connector
    • Repeat on the other side
  3. step : Removing the Radiator Cooling Fans (10:36)
    • Remove the four 10 mm bolts along the top of the front engine compartment cover
    • Lift away the front engine compartment shield
    • Slide away the black cover ring on the upper transmission cooler line on the driver side of the radiator
    • Remove the retainer spring clip on the transmission cooler line
    • Remove the upper transmission cooler line from the radiator
    • Replace the locking clip
    • Repeat for the lower transmission cooler line
    • Release the transmission cooler lines from the plastic retainer clamp at the bottom of the fan assembly
    • Squeeze the lower radiator hose clamp to slide it away
    • Remove the lower radiator hose from the radiator
    • Disconnect the two radiator fan electrical connectors
    • Pry the fan wiring retainers from the fan assembly
    • Remove the 13 mm bolt on each side of the fan assembly mounting it to the radiator
    • Lift the radiator fan assembly out of the support bracket at the bottom of the radiator
    • Squeeze the upper radiator hose clamp to slide it away
    • Remove the upper radiator hose from the radiator
    • Remove the 13 mm bolt from the radiator mounting bracket at each top corner of the radiator
    • Remove the two radiator mounting brackets
    • Remove the 13 mm bolt securing the AC condenser to the radiator on each side
    • Remove the push pin retainer from each side of the plastic shroud mounted to the AC condenser
    • Remove the plastic retaining pin from each bottom corner of the AC condenser
    • Lift the AC condenser to separate it from the radiator
    • Disconnect the hood latch electrical connector
    • Remove the two 13 mm bolts securing the hood latch to the frame
    • Remove the hood latch to allow clearance for removing the radiator
    • Remove the radiator fan assembly
  4. step : Installing the Radiator Cooling Fans (32:25)
    • Install the radiator fan assembly making sure it seats on the support brackets on the radiator, and the upper clips fit over the radiator top
    • Place the four insert nuts into the four bolt locations on the radiator for the fan assembly and the AC condenser
    • Tighten the 13 mm bolts securing the radiator fan assembly to the radiator
    • Replace the radiator fan wiring retaining clips into the fan assembly
    • Reconnect the two radiator fan electrical connectors
    • Insert the upper transmission cooler line into the radiator, making sure it engages the locking clip, and replace the plastic cover ring
    • Reconnect the upper radiator hose
    • Slide the hose clamp back into position, using the indentations as a guide
    • Place the upper radiator mounting brackets on the mounts and tighten the 13 mm bolts securing them
    • Replace the hood latch and tighten the two 13 mm bolts securing it
    • Reconnect the hood latch electrical connector
    • Seat the AC condenser onto the mounting brackets on the radiator
    • Tighten the two 13 mm bolts securing the AC condenser to the radiator
    • Replace the lower plastic shield onto the bottom of the radiator
    • Reconnect the lower transmission cooler line and replace the plastic cover ring
    • secure the transmission lines with the plastic retaining clamp
    • Reconnect the lower radiator hose
    • Slide the hose clamp back into position using the indentations as a guide
    • Replace the plastic radiator shroud and secure it to the AC condenser with the two push pin retainers
    • Replace the front engine compartment cover and secure it with the four 10 mm bolts
  5. step : Installing the Headlights (50:36)
    • Reconnect the electrical connector
    • Set the headlight assembly in place using the guide pin on the outer mounting tab as a guide
    • Tighten the lower 7 mm bolt
    • Tighten the two upper 7 mm bolts
    • Tighten the recessed 10 mm bolt
    • Repeat for the other side
  6. step : Installing the Front Bumper Cover (52:24)
    • Carefully set the bumper cover in place
    • Loosely start the top T20 screws to hold the bumper cover in place
    • Press the bumper cover retainers into the clips along the headlight and fender on each side
    • Tighten the four T20 screws along the top of the grille
    • Replace the 7 mm bolt securing the driver side bumper cover to the fender
    • Replace the four push pin retainers securing the driver side wheel well shield to the fender and bumper cover
    • Replace the two T20 screws securing the driver side wheel well shield to the bumper wheel well edge
    • Twist the driver side fog light socket clockwise to lock into the fog light housing
    • Reposition the driver side lower wheel well shield onto the underside of the bumper
    • Replace the two T20 screws securing the driver side lower wheel well shield to the underside of the bumper
    • Repeat the driver side steps for the passenger side
    • Replace the driver side engine compartment trim
    • Replace the four push pin retainers securing the driver side engine compartment trim
    • Repeat for the passenger side
  7. step : Filling the Coolant (1:02:18)
    • Connect the vacuum system to the coolant reservoir
    • Turn on the vacuum until vacuum level is achieved
    • Turn off the vacuum and wait several minutes to check for leaks
    • Insert the fill hose into a coolant bottle
    • Open the valve to fill the system
    • Switch bottles before the first one empties
    • Run the engine to remove any remaining air bubbles
    • Top off the coolant reservoir
    • Replace the cap

Tools needed for replacement:

    General Tools

  • Drain Pan
  • Pick

  • Pliers, Cutters & misc Wrenches

  • Pliers

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Sockets - Metric

  • 13mm Socket
  • 7mm Socket
  • 10mm Socket

  • Specialty Tools

  • Plastic Fastener Remover
  • Coolant Funnel Set

  • Star Drivers & Sockets

  • T20 Driver


Fits the following Makes:

Year Make Model Description
2010-2017Chevrolet Equinox Chevrolet Equinox V6 3.0L Radiator Dual Cooling Fan Assembly
2010-2017GMC Terrain GMC Terrain V6 3.0L Radiator Dual Cooling Fan Assembly

Part Interchange

Brand Label Part Number
Chevrolet 25952783
Chevrolet 25952783-PFM
DIY Solutions HVA02300
GMC 25952783-PFM
GMC 25952783
Partslink GM3115240

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

FREE SAME DAY SHIPPING
DIY Solutions
Brand #: HVA02300
Product Reviews
There are no reviews for this item.
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Customer service

877-844-3393

Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET


2010-17 Chevrolet Equinox GMC Terrain Radiator Dual Cooling Fan Assembly DIY Solutions-1ARFA00458 does not fit your:




Same Day Shipping

Orders ship same day when ordered by 2pm ET. Need your part faster? Choose expedited shipping at checkout.


Guaranteed To Fit

Providing you the highest quality, direct fit replacement auto parts enforced to the strictest product standards.


USA Customer Support

Exceeding customers' expectations every day, our team of passionate auto enthusiasts are here to help.


Instructional Video Library

Thousands of how-to auto repair videos specific to year, make and model guide you step-by-step through your repair.

Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a vehicle with these options.