Specifications:

  • Direct replacement
  • Plastic tanks with aluminum core
  • Dimensions:
    • Height: 15 11/16"
    • Width: 28 11/16"
    • Thickness: 11/16"
  • Built to strict quality control standards


 

Packaging:

Radiators may incur bent cooling fins or small imperfections during shipping or manufacturing. A few bent fins or small dents and scratches do not affect the fit or the function of the part. Neither our 60 Day satisfaction guarantee, nor the manufacturer's warranty, cover these types of insignificant damages.

Direct Fit Replacement

Core thickness equal to the OE part.  If radiator core is slightly thinner than the OEM, this can decrease overall performance and lifespan.

Premium Aluminum Core

Engineered for top performance.  Provides efficient cooling and heat-transfer.

100% Leak Tested

Built to strict quality control standards.

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Front Bumper (0:24)
    • Place tape along the edge of the bumper to mark its location
    • Remove the 10mm bolts from the splash shield
    • Remove the splash shields
    • Turn the clip in the fender liner on either side
    • Pull back the fender liner
    • Remove the 10mm bolt from the bumper on either side
    • Remove the 10mm bolt from the metal support on top of the bumper
    • Pry up the plastic pin from the headlight with a flat blade screwdriver
    • Remove the Phillips retainer from the bracket
    • Pry up the plastic pin from the headlight with a flat blade screwdriver
    • Pull the bumper off of the bracket
  2. step : Draining the Coolant (6:29)
    • Remove the 10mm bolts from the splash shield underneath the bumper
    • Remove the lower splash shield
    • Open the radiator
    • Drain the coolant into a bucket
    • Remove the radiator cap
    • Remove the 10mm bolts from the intake tube
    • Remove the intake tube
  3. step : Removing the Hood Latch (6:59)
    • Remove the three 10mm bolts from the hood latch
    • Lift the hood latch out of the vehicle
    • Lift the cable out of the bracket
    • Slide the cable end out of the latch
  4. step : Installing the Hood Latch (7:31)
    • Weave the cable behind the horn bracket
    • Slide the cable into the latch
    • Place the latch on
    • Tighten the 10mm bolts to the latch
  5. step : Removing the Upper Radiator Support (7:58)
    • Remove the 10mm bolt from the bracket on the support
    • Disconnect the horns
    • Remove the 10mm bolts from the intake tube
    • Remove the intake tube
    • Remove the two 10mm bolts on either side
    • Lift the radiator support off of the rubber mounts
  6. step : Removing the Radiator (9:41)
    • Have a drain pan ready
    • Loosen the transmission line hose clamps
    • Pry off the transmission lines
    • Place a glove over the end of the transmission lines
    • Remove the clip on the radiator hose from the O2 sensor line
    • Loosen the hose clamp on the radiator hose
    • Pry the hose off of the radiator
    • Disconnect the wiring harness from the fans
    • Pry the wire out of the clips on the fan
    • Press in the clips to separate the radiator fan
    • Lift the fan up and out
    • Undo the lower radiator hose
    • Remove the 10mm bolts from the condenser
    • Remove the radiator from the condenser
    • Remove the grommets from the bottom and top of the radiator
    • Remove the radiator cap
  7. step : Installing the Radiator (17:50)
    • Press on the cap to the new radiator
    • Press on the grommets to the new radiator
    • Press on the lower radiator hose and tighten the clamp
    • Lower the radiator into the support
    • Tighten the 10mm bolts to the condenser
    • Lower the cooling fan into place
    • Lock the fan into the radiator
    • Clip in the electrical harness
    • Connect the wiring harnesses
    • Connect the upper radiator hose
    • Connect the O2 sensor wire clip
  8. step : Replacing the Upper Radiator Support (23:12)
    • Press the support into the slots
    • Tighten the 10mm bolts on either end
    • Tighten the front bracket to the support
    • Insert the air intake
    • Tighten the 10mm bolts to the air intake
    • Connect the horns
  9. step : Installing the Hood Latch (24:31)
    • Weave the cable behind the horn bracket
    • Slide the cable into the latch
    • Place the latch on
    • Tighten the 10mm bolts to the latch
    • Insert the transmission lines to the radiator and tighten the hose clamp
  10. step : Installing the Front Bumper (27:25)
    • Hang the bumper on the top brackets
    • Push the bumper into the bracket on both sides
    • Press in the push clips to the headlights
    • Tighten the Phillips retainers to the metal bracket
    • Press in the clips to the bumper
    • Tighten the screw to the bumper behind the fender liner on both sides
    • Replace the splash shield
    • Tighten the 10mm bolts to the splash shield
  11. step : Adjusting the Hood Latch (30:05)
    • Loosen the three bolts and adjust the latch accordingly if needed
    • Close the hood and check for panel gaps
  12. step : Refilling the Coolant (30:25)
    • Slide the intake tube into place
    • Tighten the 10mm bolts
    • Close the radiator drain plug
    • Insert the splash shield into place
    • Tighten the 10mm bolts to the splash shield
    • Insert a funnel into the radiator hole
    • Top the radiator off with the correct coolant
    • Turn the heat on
    • Start the car
    • Let the engine idle and bleed any air
    • Remove the funnel

Tools needed for replacement:

    General Tools

  • Funnel
  • Small Hook
  • Drain Pan

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Anti-Freeze
  • Gloves
  • Paper Towels
  • Wire Ties
  • Painter's Tape

  • Pliers, Cutters & misc Wrenches

  • Side Cutters
  • Needle nose pliers

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Specialty Tools

  • Trim Tool Set

4.1 / 5.0
7 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
3
2
2
0
0
Matched like OEM
received it and matched the OEM that finally had to be replaced after 250K. replaced fluid and replaced thermostat/gasket as well, runs fine.
August 28, 2018
Purchased
1 month ago
Excellent quality
I really love this company. The videos that they post are very helpful and the quality of the product is excellent. Not only was the price reasonable on the radiator I purchased, I also saved hundreds of dollars on labor by not having to pay a shop to do the repair. I was able to follow along with their videos and make this radiator replacement right in the first try. I think God for 1A Auto and the parts and instructional videos they provide. I will be a repeat customer.
August 19, 2018
Purchased
1 month ago
Good fit
Fit my 2009 Camry perfectly. Good quality for the price. Got it on sale and video was accurate so I saved a lot not paying the shop. A few details left out of the video about bleeding the air and which coolant to use. Otherwise satisfied.
April 19, 2018
2008 Toyota camry radiator
Fast shipping, product showed up with a couple small holes in box from shipping. Some of the fins were bent alittle (nothing major), maybe a piece of cardboard on the inside the size of the radiator would have helped some.
Installation was easy fit right in. I did not have to take the bumper off like you's show in your youtube video though. You's should update that video. That would have sucked to take that off to find out I didn't need to.
Great product awesome price.
December 18, 2017
Purchased
9 months ago
Poor quality
It was poor quality. Also the bottom part where the screws go did not align with the AC part that goes in front of it. The fans in the back did align. It sat slightly to the right so the antifreeze hose had to be stretched to reach the radiator cap area. Everything else fit okay.
December 11, 2017
Purchased
9 months ago
Radiator
It fits well and solves my radiator problem. I highly recommend it to friends and other people to check and use 1aauto for their cars parts.
December 10, 2017
Purchased
9 months ago
Excellent Service
Just to let you know that you have the best prices ever and you have also the best Costumer service thanks so much I called for return but I was wrong it did fit on my Toyota Camry the radiator thank you for your time.
November 11, 2017
Purchased
10 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
Will this fit my 2008 Toyota Camry model ES?
Nathan on Feb 12, 2018
BEST ANSWER: This part fits the following vehicles: 2007-2009 Toyota Camry (US Built Models) Radiator L4 2.4L without Tow Package

Vehicle Fit

Year Make Model Description
2007-2009Toyota Camry Toyota Camry (US Built Models) Radiator L4 2.4L without Tow Package

This part replaces:

  • Hollander 675-50195
  • Partslink TO3010312
  • Spectra Premium Industries CU2917
  • TYC 2917
  • OE # 164000H210
Part #: 1ARAD00977


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(31:45 min)