2007-09 Toyota Camry Radiator Dual Cooling Fan Assembly - 1ARFA00498

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

Our aftermarket radiator fan assemblies are some of the highest quality replacements on the market! This radiator cooling fan assembly is a complete, ready to bolt on, direct replacement part.


  • Radiator Cooling Fan Assembly
  • Replaces dealer part numbers: 16363-0H070, 16363-0H010, 163630H070, 163630H010
  • New, not rebuilt, electric motor
  • Geometrically designed plastic blade for optimal circulation and uniform balance
  • Includes shroud, motors, & blades
  • Shroud designed to ensure structural integrity and endurance for maximum performance
  • 100% Performance factory tested
  • Replaces original assemblies that are melted or worn out
  • Comes with proper plug(s) for trouble free installation
  • Correct for 2.4L non-hybrid models WITHOUT towing package

Now you can buy a high quality radiator cooling fan motor assembly that is built to strict quality control standards. This cooling motor assembly makes a great replacement and has good cost savings over a dealer fan assembly.

Our electrical and electronic parts are subject to strict quality control testing. Please ensure proper diagnosis of this item before purchasing as the item cannot be returned once installed or plugged in.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Draining the Coolant (0:25)
    • Remove the 10mm bolts from the bottom of the bumper cover
    • Remove the 10mm bolt from the splash shield
    • Pull off the splash shield
  2. step : Draining the Coolant (1:55)
    • Have a drain pan ready
    • Open the drain at the bottom of the radiator
    • Twist off the radiator cap
  3. step : Removing the Air Intake Tube (2:29)
    • Remove the two 10mm bolts from the intake tube
    • Pull the intake tube off the air box
  4. step : Removing the Radiator Hose (3:03)
    • Unclip the O2 sensor wire from the upper radiator hose
    • Loosen the radiator hose clamps with pliers
    • Pull the radiator hose off the radiator
    • Pull the radiator hose off the engine head using a pick
  5. step : Removing the Radiator Fan (4:52)
    • Disconnect the radiator fan electrical connector with a flat blade screwdriver
    • Pry the wiring harness out of the fan with a trim tool
    • Push in the three pins at the top of the radiator fan
    • Pull the radiator fan up and out of the engine bay
  6. step : Installing the Radiator Fan (6:44)
    • Slide the radiator fan into place using the locating tabs
    • Push the radiator fan onto the push tabs at the top
    • Clip the wiring harness to the radiator fan
    • Connect the radiator fan electrical connector
  7. step : Installing the Radiator Hose (8:17)
    • Push the radiator hose onto the engine head
    • Push the radiator hose onto the radiator
    • Tighten the radiator hose clamps with pliers
    • Clip the O2 sensor wire onto the upper radiator hose
  8. step : Installing the Intake Tube (9:27)
    • Connect the intake tube to the air box
    • Line up the intake tube on the radiator support
    • Insert the two 10mm bolts that hold the intake tube to the radiator support
  9. step : Installing the Splash Shield (9:41)
    • Close the radiator drain plug
    • Lift the splash shield into place
    • Insert the 10mm bolts into the splash shield
    • Insert the 10mm bolts into the bottom of the bumper cover
  10. step : Filling the Coolant (10:13)
    • Add coolant to the radiator with a funnel
    • Start the engine
    • Turn on the heat
    • Let the engine reach operating temperature
    • Wait until the coolant stops bubbling
    • Remove the funnel from the radiator
    • Twist on the radiator cap

Tools needed for replacement:

    General Tools

  • Funnel
  • Drain Pan
  • Pick

  • Pliers, Cutters & misc Wrenches

  • Slip-Joint Pliers

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Sockets - SAE

  • 1/4 Inch Socket

  • Specialty Tools

  • Trim Tool Set

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2007-2009Toyota Camry Toyota Camry (excluding Hybrid Models) Radiator Dual Cooling Fan Assembly L4 2.4L without Tow Package
Part #: 1ARFA00498

Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(11:39 min)