2006-08 Honda Civic Fog Light Kit DEPO

Vehicle Fit
Warranty & Shipping
How-To & Tools
Product Reviews


  • Comes as a Pair
    • Fits both LH (Driver Side) & RH (Passenger Side)
  • Factory style add-on upgrade 
  • Clear Lens
  • Injection molded plastic
  • DOT (Department of Transportation) & SAE (Society of Automotive Engineers) approved
  • Includes wiring, brackets, bulbs, relay, and switch

Bulb Note:

Unless otherwise noted, our lights do not include bulbs, though occasionally lighting manufacturers do include bulbs in the lights. If you happen to receive a lighting product (Headlight, Tail light, parking light, fog light etc.) that comes with the bulbs, the bulbs are not covered under our warranty. Our warranty applies only to the light assembly.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

  1. step : Disconnecting the Battery (0:58)
    • Disconnect the negative terminal with a 10mm wrench
  2. step : Removing the Bumper Cover (1:14)
    • Pop out the clips from the lower splash shield
    • Remove the Phillips head screw from the opening in the splash shield
    • Remove the push clips from the plastic air guide in the engine compartment
    • Pull the air guide out of the engine compartment
    • Remove the T35 Torx on the grille bolts from the brace
    • Pull the bumper cover out of its clips
    • Pull the bumper cover off of the car
  3. step : Removing the Fog Light Cut Out (5:20)
    • Place tape around the interior sides next to the grille
    • Place a push pin into the center of bulls eye markers on the back of the bumper cover
    • Drill a hole through the bulls eye with a 1/4 inch drill bit
    • Drill a hole through the bulls eye with a 1/4 inch drill bit
    • Cut along the molded line with a hacksaw
    • Remove the bumper cutout
    • Cut off the edge of highest and lowest side wall on the grille with a box cutter
  4. step : Installing the Fog Light (9:30)
    • L is driver side
    • R is passenger side
    • Place the bracket mount onto the fog light
    • Place the bracket mounts to each fog light
    • Tighten the Phillips screws to the fog light
    • Insert the fog light into the bumper
    • Make sure the adjustment bracket does not touch the plastic
    • Cut out more of the bumper cover if necessary
    • Tighten the Phillips screws to the bracket
    • Place the corresponding trim cover to the light
    • Tighten the two Phillips screws to the fog light cover
  5. step : Wiring the Lights (18:41)
    • Insert the wire behind the radiator support and behind the condenser to the other side
    • Wire tie the wire to the brace
    • Bring the wire up behind the headlight past the battery
    • Pry out the clips from the wheel well
    • Pull the wheel well down
    • Run the wiring harness through the wheel well
    • Wire-tie the wiring harness through the wheel well
    • Pry the grommet out of the body
    • Punch a hole through the grommet with a pick
    • Push the wiring through the grommet
    • Insert the wiring and grommet into the body
    • Insert the wheel well into place
    • Press the clips into the wheel well
    • Bundle the wiring next to the horn
    • Connect the relay by the battery
    • Mount the on the 10mm bolt by the radiator support
    • Place a ground underneath the bolt
    • Loosen the positive battery terminal
    • Tighten the positive lead to the positive terminal
    • Bundle and wire tie the positive and negative wires to the wiring next to the horn
    • Wrap up the wires with electrical tape
    • Strip the wire with a wire stripping tool
    • Connect add-a-fuse with a butt connector
    • Wrap electrical tape around the butt connector
  6. step : Installing the Switch Plate (31:12)
    • Pull off the lower dash
    • Remove the Phillips screw from the upper dash
    • Pop the upper trim off of the dash
    • Disconnect the cruise control connector
    • Remove the three Phillips head screws from the pocket
    • Remove the pocket from the dash
    • Press the switch bezel into place
    • Tighten the three Phillips screws to the bezel
    • Press the upper dash panel into place
    • Connect the cruise control connector
    • Tighten the Phillips screw to the upper trim
    • Connect the red wire with the butt connector to the wire inserted through the fender
    • Zip tie an excess wire
    • Remove the fuse from spot 37
    • Insert the add-a-fuse into place
    • Connect the ground wire to the bolt in the fuse panel
    • Run excess wire into the dash opening
    • Press the switch into place
    • Connect the wiring harness to the switch
    • Press the extra caps into the switch plate
  7. step : Reinstalling the Bumper Cover (41:19)
    • Connect the fog light wiring harness
    • Hang the bumper up into place
    • Press the bumper into the brackets
    • Remove the tape from the bumper cover
    • Tighten the Phillips screws to the fender
    • Tighten the Phillips screws to the bracket
    • Insert the air guide into place
    • Press the clips to the guide
    • Press the clips to the bumper
  8. step : Reconnecting the Negative Battery Terminal (45:32)
    • Tighten the negative terminal with a 10mm wrench

Tools needed for replacement:

    Drills, Drill Bits & Related

  • Drill

  • General Tools

  • Utility Knife
  • Pick

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Electrical Tape
  • Wire Ties
  • Painter's Tape

  • Pliers, Cutters & misc Wrenches

  • Wire End Cutters
  • Side Cutters
  • Needle nose pliers
  • Wire Cutters

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 12mm Socket
  • 10mm Socket

  • Star Drivers & Sockets

  • T35 Torx Socket

  • Wrenches - Metric

  • 10mm Wrench
  • 12mm Wrench

There are no reviews for this item.
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.

Fits the following Makes:

Year Make Model Description
2006-2008Honda Civic Honda Civic Sedan Upgrade Fog Light Kit
Part 1ALFP00036

Out of Stock

Brand #: 317-2017P-AS