2008 Subaru Outback Rear Driver & Passenger Side 2 Piece Strut & Spring Assembly Set TRQ SCA57160

Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!

In this video, we are replacing rear struts in a 2008 Subaru Outback. If you need these parts or other parts for your car, click the link in the description and head over 1AAuto.com.

Open the back. Pull this up and out. Pull this up. See the clips underneath here. Fold down the back seats, push that down, and push that one down. This folded up here like that. And then take these two upper strut mount nuts off, and then put a 14 millimeter wrench on. And we'll break these free with a 14 millimeter wrench. Going to take off the lug nuts. It's a 19 millimeter socket and a breaker bar. I'm just going to crack them loose before we lift the vehicle off the ground. Take the lug nuts off.

From the side grab the wheel, pull it off. All right, then we're going to take the shock bolt out here, with a 19 millimeter socket and a 19 millimeter wrench. Pull the nut off. It's a good idea to support the lower suspension with… we're using a screw jack, but you could use a floor jack or a piece of wood or something underneath. The suspension may fall or go up once we pull that bolt out. To pull that out, I'm going to use a punch. Punch it through. As this goes through the shock is going to fall, so I'm going to try to support it. Be able to pull it down. Pull it straight down. We could have left a, one of the nuts on top so that it wouldn't fall all the way—you can also do that.

This is our old spring and strut assembly. This is our new spring and strut assembly from 1AAuto.com. As you can see, they are almost identical. It doesn't matter left to right—they're both the same part number.

On here you're going to see this warning. It tells you not to touch this nut underneath here, because it could be dangerous. It's safer to install the strut spring assemblies as a whole, versus removing the strut and taking a compressor and putting a new strut on. You don't have to mess around with it—it's good to pop right in. Order your part from 1AAuto.com and you'll be ready to rock and roll.

As you can see, when we took our strut spring assembly out, the suspension actually raised up. Most of the time when you're doing that, the suspension will kick down. For this vehicle it went up. All right, I'm going to install the new strut, this way and then I'm going to line up the holes on top. As that's in there, while I'm holding up I'm going to take one of the nuts and go around, get that nut started so it holds it up in place first.

So we're going to support the lower part of the shock strut assembly, but we also want to pry down on the suspension. I'm going to use a pry bar. Feed it through there and hold it against the frame. And while we're pulling down, try to get the bolt in. There we go. Once you get it started, you can take this down. Get this out of your way. And just tap it with a hammer. Put the nut back on.

Another way to get that bolt in for the lower strut: You could also put in a jack right here, if you had like a scissor jack. Could have stuck it in there and then be able to push the control arms down and then fish that bolt in and you'd be good. Now we're going to tighten the bolt up, the nut. 19 millimeter wrench and a 19 millimeter socket and ratchet. Now we're going to torque this bolt to 46 foot-pounds. That's good.

Install our tire. Put the lug nuts on. With a torque wrench, we're going to torque the lug nuts down to 90 foot-pounds going in a star pattern. You want to go in a star pattern so that you torque the wheel to the hub evenly. The struts come with new nuts, they're 15 millimeter instead of 14 millimeter. So I'm going to put these on. It's kind of hard to get underneath here. And the torque on these nuts is 22 foot-pounds. It's hard to get a torque wrench in there, so I'm just going to use a wrench.

And reinstall this. This piece comes up and over like that. There's a little push pin that goes right there, like that. Push the back seats up. Install the back panels. These two little clips go in there. Line them up and push them down. This one actually popped out over here. Put that clip in there first. Put this on here. Push it down. Just going to line those two tabs up in the back, and push that down. Close the deck lid.

Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.