• Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side)
  • Includes lenses & housings
  • Bulbs not included
Direct Fit Replacement

Direct fit replacement for OEM assembly

Trouble-free Installation

Uses same wiring as original assembly.  No cutting or splicing required.

DOT and SAE Compliant

Meets federal regulations for on-road use

Part Details

  • Quantity: Pair

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Changing the Bulbs (0:47)
    • To replace the turn signal twist the socket up and pull and push the bulb down and twist to remove it.
    • Put the new bulb in and twist then replace the socket and twist it down.
    • For the headlight remove the cap and pull off the connector.
    • Push the clip down and off and pull the bulb out.
    • Replace the bulb with the notch at the top.
    • Replace the clip and harness. Then twist on the cap.
    • Next to the headlight bulb there is a day time light that can be twisted out and the bulb pulls straight out.
  2. step : Replacing the Headlight Assembly (2:54)
    • Remove the two 10mm bolts at the top of the headlight.
    • Use an extension to get the third 10mm bolt down behind the headlight.
    • Remove the two connectors from the back of the headlight by pushing the tabs and pulling out.
    • Pull the grille side of the headlight and pull the assembly free.
    • Insert the new headlight assembly outside first.
    • Replace the three 10mm bolts.
    • Replace the connectors.
  3. step : Adjusting the Headlights (5:34)
    • Use a screwdriver in the adjustment screw on the back of the headlight to adjust the headlight up and down.
    • Clockwise is up and counterclockwise is down.
    • Aim the headlight at a wall 20ft away. Aim the concentration of the light one inch below the bulb.
  4. step : Removing Drivers Side Shield (6:24)
    • To remove the headlight assembly or change a bulb on the drivers side you need to remove the shield.
    • Use a Phillips screwdriver to twist the center up and pull the clip out.
    • Use a 10mm socket and ratchet to remove the bolt at the top of the shield.
    • Remove the shield.

Tools needed for replacement:

    Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Sockets - Metric

  • 10mm Socket

4.6 / 5.0
8 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Worked Great
Easy to install, new headlights work great. Good value for money.
May 19, 2018
2 months ago
Products were received in good condition.
Installation video was simple and yet informative.
Only problem was that the original bulb holding connection had to be slightly forced in as the slots were not completely cut out. I did not use the bulbs that came with the set. I'll use them later.
The headlights improved the appearance immediately.
January 26, 2018
6 months ago
Excellent as Usual
Correct part sent timely and I always use your store for my parts. Thanks.
November 27, 2017
8 months ago
Excellent, considerate service
In addition to excellent service, the products arrived in a short time. Just a little more than one week.
July 27, 2017
1 year ago
Piece of cake!!
They fit easy and were a snap to install. Had a small Hiccup, had to move the battery to install the driver side. Other than that the whole job beginning to end was about 40 minutes. Makes a huge difference in the look of the car as well as the visibility gained with crystal clear globes. Well worth the money and effort. Do it !!!
July 11, 2017
1 year ago
July 3, 2017
1 year ago
headlight pack
cost and expedient shipping were fantastic. instructional video was extremely helpful. i am presently in the process of resolving an issue with the left headlight. seems there was no adjusting screw. 1A Auto is working to resolve this issue as I write my review.
April 23, 2017
1 year ago
Tough fit, alignment and the passenger light is not sealed.
I like the ease of placement bu the lights don't adjust well. The big problem is, they are poorly made. The passenger side let's moisture in and condensation forms when it is driven in the rain. Honestly I would like this one replaced. I am not satisfied. I wonder...will this issue be resolved?
February 18, 2017
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2004-2006 Hyundai Elantra Headlight Pair

This part replaces:

  • OE # 921012D550
  • OE # 921022D550
  • Partslink HY2503130, HY2502130
Part #: 1ALHP00533

How-to Video:

(07:16 min)