1APAI00188-2003-08 Dodge Ram 1500 2500 3500 Performance Air Intake Kit

Replaces

2003-08 Dodge Ram 1500 2500 3500 Performance Air Intake Kit DIY Solutions

1APAI00188

Part Details

  • Product Line: Performance
  • Includes: Red Filter
  • Finish: Polished Aluminum
  • Tubing Diameter: 3 in. (76.2mm) Diameter Tubing

This part replaces:

  • DIY Solutions FLT00189
FREE SAME DAY SHIPPING
Save 27%
List: $102.95 Save: $28.00
Only 7 left in stock
Part 1APAI00188
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

DIY Solutions
Brand #: FLT00189

Frequently bought together

Description
Vehicle Fit
Warranty & Shipping
How-To & Tools
Q&A

Part Details

  • Includes:   Red Filter
  • Tubing Diameter:   3 in. (76.2mm) Diameter Tubing
  • Finish:   Polished Aluminum
  • Product Line:   Performance

This product is not C.A.R.B. approved and is intended for off-road use only.  It is the purchaser's responsibility to determine their local, state, and federal laws and regulation.

 

Your DIY Solution—Complete Repair in One Purchase

Do you need an assortment of parts to complete a repair? Stop searching for parts individually and complete your repair in a single purchase with a customized kit or set from DIY Solutions.

High-Quality Parts From Trusted Brands

Parts in DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.

Guaranteed Fit

DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Cadmium and Cadmium Compounds, which is known to the State of California to cause cancer and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

California Emissions Note:

Due to state emissions regulations, we cannot ship this item to the state of California as it is not C.A.R.B (California Air Research Board) approved for use in this state.

  1. step : Removing the Air Intake (0:46)
    • Release the clips and open the air filter housing box
    • List the air filter housing box cover up and off
    • Release the PCV hose
    • Loosen the rear clamp on the inlet pipe
    • Remove the box cover and pipe
    • Lift the bottom of the air filter housing box up and out
    • Remove the 10mm bolt behind the alternator
    • Remove the 10mm bolt behind the oil cap
    • Lift the air box up
    • Disconnect the intake sensor
    • Remove the air box
  2. step : Preparing the Performance Intake Kit (2:07)
    • Press the thinner end of the gasket onto the heat shield around the bends
    • Remove the rubber bushings from the air box
    • Press the rubber bushings into the Z and medium-sized L Bracket
    • Press the Z bracket onto the bottom of the heat shield
    • Insert the 11mm bolts and washers to Z bracket and shield
    • Tighten the bolts loosely
    • Insert the 11mm bolts and washer to the medium L bracket and shield
    • Tighten the bolts loosely
    • Press the 11mm rubber insulated nut to the short twisted bracket and tighten it
    • If your truck has an EGR, use the long, straight bracket
    • If your truck does not have EGR, use the long, twisted bracket
    • Place the intake tube collar and space onto the single drilled hole of the bracket
    • Insert the washer and 11mm nut to the bottom of the bolt
    • Support the other end of the bolt with a 4mm Allen lock key
    • Tighten the 11mm nut loosely
    • Press the rubber grommet to the air intake tube
    • Remove the air intake temp sensor from the air box
    • Remove the O-ring from the air sensor if you have it
    • Press the air sensor into the rubber grommet on the air intake tube
  3. step : Installing the Heat Shield (6:53)
    • Remove the 13mm bolt from the fan shroud just below the radiator fill
    • Insert the bolt to the bigger slotted hole on the small L bracket by hand
    • Remove the 13mm bolt behind the hood strut on the air box bracket
    • Insert the slotted hole on the twisted bracket with the rubber insulated nut to the air box
    • Tighten the 13mm bolt to the bracket
    • Insert and press the heat shield into place
    • Insert the shorter hardware into the insulated nut
    • Insert the hardware to the small L bracket
    • Tighten all the bolts
  4. step : Installing the Intake Hose, Filter, and PCV Hose (9:26)
    • Remove the clamp from the PCV breather hose
    • Install the silicone cuppling with the hose clamps to the throttle body
    • Tighten the throttle body-side hose clamp with a flat blade screwdriver
    • Insert the intake tube bracket to the front bolt that held the upper air box
    • If your vehicle does not have an EGR, read the instructions to find appropriate bracket placement
    • Test-fit the intake tube
    • Tighten the bolt to the bracket
    • Insert the hose clamp over the intake tube and insert the tube into place
    • Tighten the hose clamp near the heat shield with a flat blade screwdriver
    • Reconnect the IAT sensor
    • Insert the intake cone onto the intake tube
    • Tighten the hose clamp near the throttle body
    • Insert the PCV breather into the slot below the oil fill neck
    • Insert the PCV breather to the fitting on the intake hose
    • Tighten the clamps with needle nose pliers
    • Turn on the engine to make sure everything's working

Tools needed for replacement:

    Hex Wrenches

  • 4mm Hex Wrench

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 11mm Socket
  • 10mm Socket
  • 13mm Socket

  • Wrenches - Metric

  • 11mm Wrench
  • 13mm Wrench
  • 10mm Wrench

Need help? Ask one of our Auto Experts
Need help? Ask one of our Auto Experts
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Hi I have 2005 ram with the air intake system I was wondering whats the diameter of the air filter? I need replacement
Robert G January 16, 2017
Hello Robert. If you already have an upgraded air intake system the you will simply have to measure the air filter you currently have on it. From there you will be able to find a replacement that will fit.
Tim K January 16, 2017
Does the kit come with the black box?
Camden C December 4, 2017
No it doesnt have the heat shield. It comes as pictured.
Woodrow M December 4, 2017
No, I returned it and spent the money for the actual K&N complete kit.
D O December 4, 2017
Hey Camden, I purchased this unit and it does not come w a black box. Hope it helps you!
S A December 4, 2017
Does this kit come with a heat shield like in the video?
Jack J February 7, 2019
No it doesnt
B I February 7, 2019
This item will not include the heat shield.
Emma F February 7, 2019
No I ended up buying the K&N kit which is what the video shows.
D O February 10, 2019
Will it fit or work for my 4.7 doge ram 1500?
J O July 7, 2020
Thank you for the inquiry! This will not work on the 4.7L. We can check to see if we have a kit for your engine size. Can you please confirm the year of your Dodge Ram 1500?
Andra M July 8, 2020

Fits the following Makes:

Year Make Model Description
2003-2008Dodge Ram 1500 Truck Dodge Ram 1500 Truck V8 5.7L Performance Air Intake Kit
2003-2008Dodge Ram 2500 Truck Dodge Ram 2500 Truck V8 5.7L Performance Air Intake Kit
2003-2008Dodge Ram 3500 Truck Dodge Ram 3500 Truck V8 5.7L Performance Air Intake Kit

Part Interchange

Brand Label Part Number
DIY Solutions FLT00189

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

FREE SAME DAY SHIPPING
DIY Solutions
Brand #: FLT00189
Product Reviews
3.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
0
0
1
0
0
Air flow sensor
My air flow sensor didnt reach so i had to buy an adaptor to make it reach..
March 11, 2019
Customer service

877-844-3393

Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET


2003-08 Dodge Ram 1500 2500 3500 Performance Air Intake Kit DIY Solutions-1APAI00188 does not fit your:


Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a vehicle with these options.