1ASFK02792-2003-07 Cadillac CTS Steering & Suspension Kit 8 Piece Set


2003-07 Cadillac CTS Steering & Suspension Kit 8 Piece Set TRQ PSA59020


Part Details

  • Kit Includes: (2) Front Lower Ball Joints
  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Steering Rack & Pinion Bellows
  • Kit Includes: (2) Front Inner Tie Rods
  • Quantity: 8 Piece Set

This part replaces:

  • Moog K80635
  • Moog EV800332
  • Moog ES3586
  • Moog ES3585
  • OE # 89047662
  • OE # 88892773
  • OE # 88892774
  • OE # 88892776
Save 21%
List: $94.95 Save: $20.00
Part 1ASFK02792
In Stock

Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Brand #: PSA59020

Frequently bought together

Vehicle Fit
Warranty & Shipping
How-To & Tools

Part Details

  • Quantity:   8 Piece Set
  • Kit Includes:
      (2) Front Lower Ball Joints
      (2) Front Outer Tie Rods
      (2) Steering Rack & Pinion Bellows
      (2) Front Inner Tie Rods


  • Comes as a 8 Piece Kit
    • Fits both LH (Driver Side) & RH (Passenger Side) Front
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

    Regarding alignments, it's suggested that you have an alignment performed after you do a replacement like this.

  1. step : Testing the Tie Rod (0:15)
    • Jack up one of your front wheels
    • Grab it by the sides of the tire and try to move it back and forth. If you feel more play than just the steering rack moving back and forth, then your tie rod probably needs replacing
  2. step : Removing the Front Wheel (0:56)
    • If you don't have air tools, you'll want to loosen the lug nuts with the wheel on the ground
    • Lift the vehicle with a jack, support it with a jack stand, and take the wheel off the rest of the way
  3. step : Measuring the Tie Rod (1:19)
    • Before you disassemble the tie rod, you want to measure the tie rod
    • From a fixed point on the rack, like the end of the boot, you want to measure to the middle of the tie rod
    • Measure a few times to be sure-you're going to set the new tie rod up the same length
  4. step : Removing the Tie Rod (1:58)
    • You'll see a lock nut at the end of the tie rod. Holding on to the tie rod with a wrench, use your adjustable wrench to loosen that nut about a quarter of a turn
    • There is also am 18 mm bolt that nut that holds the stud on. Remove that
    • Separate the tie rod from the steering knuckle by using a tie rod fork. Taking a hammer, you'll drive the tie rod fork between the rod and the knuckle
    • Once the tie rod is separated from the knuckle, turn it clockwise to get it off the steering rack
  5. step : Replacing the Tie Rod (3:45)
    • The new tie rod should come with the bolt in it. Take the bolt out for now.
    • Thread the tie rod onto the nut, measure from the same fixed point as before and make sure it measures the same. Take a couple of measurement.
    • Also, make sure you do not twist the shaft that comes out of the steering rack. Doing so will change your alignment.
  6. step : Securing the New Tie Rod (4:39)
    • Once you have the measurement correct, then you can put the tie rod back into the steering knuckle and start the bolt on there
    • The lock nut at the end of the tie rod is an 18 mm nut. Holding the stud of the tie rod with an 8 mm wrench, tighten up the nut with your 18 mm wrench
    • Once the 18 mm wrench is tight, grab another wrench and hook it on there for leverage. Give it another pull just for good measure
    • Torque it to 65 foot pounds
    • Put your wrench onto the inner tie rod to get this locking nut back out against the outer tie rod. Tighten
  7. step : Replacing the Wheel (5:53)
    • Turn the wheels straight, and put your wheel and tire back on
    • Start the lug nuts by hand at first to primarily tighten them.
    • Lower the car back onto the ground
    • Set your torque wrench to 90 - 95 foot pounds and tighten your lug nuts in a star pattern

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Torque Wrench

  • Sockets - Metric

  • 18mm Socket
  • 19mm Socket

  • Specialty Tools

  • Tie Rod Fork

Need help? Ask one of our Auto Experts
Need help? Ask one of our Auto Experts
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.

Fits the following Makes:

Year Make Model Description
2003-2007Cadillac CTS Cadillac CTS Steering & Suspension Kit 8 Piece Set

Part Interchange

Brand Label Part Number
Beck / Arnley 103-2842
Beck/Arnley 103-2842
DIY Solutions SUS07794
DIY Solutions SUS07527
DIY Solutions SUS07528
DIY Solutions SUS07526
DIY Solutions SUS00322
General Motors 88892773
General Motors 88892776
General Motors 88892774
MOOG EV800332
MOOG K80635
MOOG Chassis Products ES3586
MOOG Chassis Products ES3585
MOOG Chassis Products EV800332
MOOG Chassis Products K80635

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

Brand #: PSA59020
Product Reviews
5.00/ 5.0
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
exactly what I needed
They were the exact parts I was looking for installation was easy my only issue was the delivery I paid for overnight it was delayed by The courier but 1aauto refunded my money for my delivery so I have nothing but praise for their company and parts.
August 31, 2019
Customer service


Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET

2003-07 Cadillac CTS Steering & Suspension Kit 8 Piece Set TRQ PSA59020-1ASFK02792 does not fit your:

Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a vehicle with these options.