Kit Includes: (1) Windshield Wiper Motor & Linkage (1) Wiper Motor Jumper Harness (Oval Connector to Square)
Genuine original equipment part (OEM) that was factory installed on your vehicle by the manufacturer.
Item Condition:New
Attention California Customers:
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
1 Year Warranty
This item is backed by our 1-year warranty. In the event this item should fail during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
How to Replace Windshield Wiper Motor Linkage 2004-10 Dodge Ram
Created on:
Tools used
Socket Extensions
10mm Socket
Ratchet
Wire Cutters
T25 Torx Driver
1. Removing the Wiper Arms
Lift the wiper arm up
Pull out the tab on the end of the arm
Slide the arm off the splines
2. Removing the Wiper Cowl Cover
Remove the T25 Torx screws from both ends of the cowl
Pry out the snap clips from the cowl with side cutters
Remove the deadening material
Remove the weatherstrip
Lift up the passenger side wiper cowl
Disconnect the washer hoses from their retainers
Remove the passenger side wiper cowl
Remove the clips from the driver's side
Remove the wiper cowl cover from the vehicle
3. Removing the Wiper Motor and Linkage
Disconnect the wiper motor electrical connector
Remove the three 10mm bolts from the wiper linkage
Remove the wiper motor and transmission assembly
4. Installing the Wiper Motor and Linkage
Change over the rubber protector piece to the new wiper motor and linkage
Insert the wiper motor and linkage into place
Tighten the three 10mm bolts to the wiper linkage
Connect the wiper motor electrical connector
5. Installing the Wiper Cowl Cover
Insert the wiper cowl into place
Press the clip connectors into place
Snap the washer hoses into the cowl cover
Realign the passenger side cowl cover
Insert the weatherstrip into the cowl
Tighten the two T25 Torx screws
6. Reinstalling the Wiper Arms
Press the arm onto the splines
Close the clip
Lay the wiper arm down
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks. In this video, we're going to show you how to remove and reinstall the wiper cowl cover in this 2008 Dodge Ram 1500.
Here are the items you'll need for this repair: T25 Torx Drivers, side cutters
Remove the wiper arms from the truck. You have to lift up. Small tab here that you take out with your thumb. It simply lifts off the splines. Using a T25 Torx bit ratchet and extension, remove the T25 Torx screws on both ends of the wiper cowl. Open your hood.
We're going to use a pair of side cutters to remove all of these plastic snap clips here. It makes them a lot easier to pry out. What you want to do is open them up, slide them underneath, and close down without cutting. Simply work it back and forth. Repeat this for the remaining clips all the way down the bottom of the wiper cowl.
We'll also remove this clip on the insulation. Pull that back. Lift up on the weather strip here. That simply pulls off. Now we can remove the passenger side of our wiper cowl. Disconnect the windshield washer lines there. Remove the remaining three clips. Take off our driver's side. Remove the wiper cowl cover.
Reinstall your wiper cowl. Reconnect to your plastic clip connectors. Reconnect the washer hoses. Snap them down into the retainers. Reinstall plastic clips. Lay this deadening material back across. Stick this harness retainer in and the other clip. Lay the weather strip across the bottom of the cowl. Snap it onto its retainer in the middle here. Close your hood. Reinstall the two Torx screws at the rear of the cowl. Reinstall the wiper arms onto the splines.
Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.
MPERK00002
In Stock
Product Reviews
Loading reviews
There are no reviews for this item.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.