This is a new replacement Ford Escape Fog Light or Driving Lamp. In general the bulb itself is not included.

Specifications:

  • Fits RH (Passenger Side)
  • Replaces dealer part numbers: YL8Z-15200-AA, YL8Z15200AA
  • Direct replacement fog light
  • (DOT) Department of Transportation and (SAE) Society of Automobile Engineers approved.
  • Assembly includes lens, housing, and mounting bracket
  • Built to strict quality control standards

Direct Fit Replacement

Direct fit replacement for OEM assembly

Trouble-free Installation

Uses same wiring as original assembly.  No cutting or splicing required.

DOT and SAE Compliant

Meets federal regulations for on-road use

Part Details

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Bulb Note:

Unless otherwise noted, our lights do not include bulbs, though occasionally lighting manufacturers do include bulbs in the lights. If you happen to receive a lighting product (Headlight, Tail light, parking light, fog light etc.) that comes with the bulbs, the bulbs are not covered under our warranty. Our warranty applies only to the light assembly.

  1. step : Servicing the Fog Light Bulbs (0:53)
    • Remove the three 10mm bolts from the splash shield
    • Pull back the splash shield
    • Twist the bulbs counterclockwise out of the fog light
    • Disconnect the bulb from the wiring harness
    • Connect the new bulb to the wiring harness
    • Twist the bulbs clockwise into the fog light
    • Push the splash shield into place
    • Insert the three 10mm bolts into the splash shield
  2. step : Removing the Bumper (2:03)
    • Remove the two 10mm bolts from the top of the bumper
    • Remove the three plastic clips from each inner fender with a Phillips head screwdriver
    • Remove the two plastic clips from underneath the grille with a Phillips head screwdriver
    • Remove the two plastic clips behind each inner fender with a Phillips head screwdriver
    • Remove the series of 10mm bolts underneath the bumper
    • Apply penetrating oil to the bolts as necessary
    • Disconnect the wiring harnesses from the fog lights
    • Pull off the bumper
  3. step : Replacing the Fog Lights (6:01)
    • Remove the three 8mm or 10mm bolts from each fog light
    • Pull off the old fog lights
    • Push the ne fog lights into place
    • Insert the three 8mm or 10mm bolts into each fog light
  4. step : Reinstalling the Bumper (8:16)
    • Lift the bumper into place
    • Start the two 10mm bolts into the top of the bumper by hand
    • Make sure the splash shield overlaps the bumper
    • Insert one 10mm bolt into the bottom of the bumper
    • Insert the two plastic clips behind each inner fender
    • Insert the two plastic clips underneath the grille
    • Insert the series of 10mm bolts into the bottom of the bumper
    • Insert the three plastic clips into each inner fender
    • Tighten the two 10mm bolts into the top of the bumper

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 8mm Socket
  • 10mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2001-2004 Ford Escape Fog / Driving Light Passenger Side

This part replaces:

  • Partslink FO2593190
  • Hollander 116-03156R
  • OE # YL8Z15200AA
  • TYC 19-5677-00-1
  • DEPO 330-2018R-AF
Only 4 left in stock
Part #: 1ALFL00065

How-to Video:

(08:43 min)