Replaces
2000-05 Chevy Impala Window Regulator - 1AWRG00436
1AWRG00436Specifications:
- Fits RH (Passenger Side) REAR
- Assembly includes motor and regulator
- Replaces dealer part numbers: 10338856, 88987652
- 100% tested prior to leaving the factory
Please Note: This window regulator is a high quality aftermarket part that meets or exceeds the performance of the original. It has been subjected to extensive testing and quality control standards. That is why we offer this regulator with our superior warranty!
Installation
- This repair is easier than you may think. You'll find our installation videos helpful. In our experience removing and replacing the door panel is the most involved step in the repair. On most vehicles this only requires removing a few screws and push-in clips.
- You'll get a great feeling of accomplishment after you complete this repair knowing you saved money, and you didn't have to give up your car for a day at the repair shop. Your passengers and other drivers will be amazed.
Fit guaranteed
- 1A Auto will refund you with no hassle, if this window regulator does not fit the application stated.
- This regulator will install just as your original does. Save time and money.
Quality
- Be confident this part will work right. Every regulator is tested after assembly to make sure all mechanisms are working correctly.
- It is important that your new regulator works for a long period of time. The design of this regulator is tested to withstand 10,000 cycles. That is enough to raise and lower your window 3 times per day for 9 years.
Value
- Windows that don't work can be frustrating. They can also hurt your vehicles value. An inoperable window could mean $200-$500 discounted off a dealer trade value or asking price.
- Some shops and dealers charge more for parts and repairs when they think you don't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly repair bill.
Direct fit, pre-assembled parts made ready to fit your vehicle and provide easy and trouble-free installation.
Rigorously TestedBuild to strict quality standards
Highest Quality MaterialsMade from the highest quality materials for extreme durability and premium performance.
Lifetime Warranty
This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.
-
step : Removing the Door Panel (1:03)
- Remove the Phillips head screw inside the door handle
- Remove the two T30 Torx screws inside the door pull
- Pry off the window switch panel
- Pry off the door handle bezel
- Disconnect the window switch wiring harness
- Remove the two T30 Torx screws behind the door pull
- Pry off the window trim panel
- Pry out the door panel with a door panel clip tool or putty knife
- Lift the door panel up and off
-
step : Removing the Window Regulator (3:40)
- Remove the three 10mm bolts from the regulator
- Loosen the two 10mm bolts that hold the window to the regulator
- Raise the window by hand
- Hold the window in place with painter's tape
- Remove the three 10mm bolts from the window motor
- Disconnect the window motor lead
- Pull the window regulator out through the door
-
step : Reinstalling the Regulator (7:46)
- Transfer the motor to the new regulator
- Push the regulator into the door
- Hang the regulator by its motor bolts
- Connect the window motor lead
- Insert the three 10mm bolts into the regulator
- Insert the three 10mm bolts into the window motor
- Remove the painter's tape from the window
- Lower the window onto the regulator
- Insert the two 10mm bolts that hold the window to the regulator
-
step : Reinstalling the Door Panel (10:57)
- Make sure the insulation is in place
- Lift the door panel into place, using the locating pins
- Push in the door panel clips
- Push on the window trim piece
- Insert the two T30 Torx screws behind the door pull
- Push on the door handle bezel
- Insert the Phillips head screw inside the door handle
- Connect the window switch wiring harness
- Push the switch panel into place
- Insert the two T30 Torx screws inside the door pull
Tools needed for replacement:
- Putty Knife
- Painter's Tape
- Ratchet
- Socket Extensions
- Phillips Head Screwdriver
- 10mm Socket
- Door Panel Removal Tool
- T30 Torx Driver
General Tools
Materials, Fluids, and Supplies
Ratchets & Related
Screwdrivers & Related
Sockets - Metric
Specialty Tools
Torx Drivers & Sockets
- Was this review helpful? Yes (1) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (1) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Vehicle Fit
- 2000-2005 Chevy Impala Rear Power Window Regulator with Motor Passenger Side
This part replaces:
- OE # 10338856
- OE # 88987652
- Hollander 135-01803
- Dorman 741-623
- TYC 660221