Replaces

2000-04 Ford Focus Steering & Suspension Kit - 1ASFK03088

Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 12 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Accessing the Shocks and Struts (1:03)
    • Loosen the lug nuts on the wheel while the car is on the ground
    • Jack the car up and remove the lug nuts and wheel
    • Pull the brake line from the bracket
    • Pull the ABS sensor out of its bracket
    • Remove the bolt on the upper stabilizer link. Spray with penetrating oil
    • Spray the bolt on the back side of the strut with penetrating oil
    • Use a socket to remove the 15mm bolt on the steering knuckle
  2. step : Removing the Strut (4:27)
    • Spray penetrating oil where the strut connect with the steering knuckle
    • Use a 15mm socket to disconnect the tie rod. Use a jack and some wood to hold the tie rod up to help remove the bolt
    • If the vehicle has a broken spring lift up on the strut and hammer the steering knuckle until it loosens
    • Lift the strut up and out of the steering knuckle
    • Remove the three 13mm bolts up in the engine compartment
    • Pull the strut free
  3. step : Installing a New Strut (6:40)
    • With the clip on the bottom of the strut facing inward, put the strut into place
    • Replace the bolts in the engine compartment
    • Pull the steering knuckle out and slide it on to the bottom of the strut
    • Replace the bolt that connects the strut to the steering knuckle. Do not tighten fully
    • Make sure the steering knuckle is below the taper on the strut
    • Make sure its at the right depth and moves properly
    • Tighten the bolt on the steering knuckle to between 65 and 70ft/lbs
  4. step : Reconnecting the Brackets and Sensors (9:52)
    • Put the brake line back in place
    • Put the tie rod back in place and replace the nut
    • Replace the stabilizer link and bracket. Tighten the nut
    • Put the ABS sensor back in place
    • Jack the tie rod up and tighten the nut to 55 to 60ft/lbs
    • Replace the wheel and thread the lug nuts
    • Lower the car and tighten the lug nuts to 100ft/lbs in a crossing pattern
    • Tighten the bolts in the engine compartment to between 25 and 30ft/lbs

Tools needed for replacement:

    General Tools

  • Hammer

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Sockets - Metric

  • 13mm Socket
  • 15mm Socket
  • 17mm Socket
  • 19mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Driver

  • Wrenches - Metric

  • 17mm Wrench

5.0 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
2
0
0
0
0
Just What I Needed
This kit is great, has literally everything you need to completely freshen up a tired front end minus some odd hardware you made consoder replacing. Everything fit as it should, shows solid quality for a daily driver, went in without a hitch. Order was handled quickly as well as the delivery, and I've yet to find a better price. 10/10, I'll certainly be back.
April 8, 2018
Purchased
2 months ago
My 2002 ford Focus ZX3
Keep the prices really good keep the quality really good I will definitely continue to keep on ordering if prices go up quality goes down you will lose me as a customer thank you for the good service from customer care whenever I have a problem
June 26, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 2 answers
Does this include replacement bolts as well?
Kurtisc94 on Apr 17, 2018
BEST ANSWER: The kit you see comes just as pictured, and it does not come with any new mounting hardware for the control arms or struts.

Vehicle Fit

  • 2000-2004 Ford Focus 12 Piece Set Steering & Suspension Kit (excluding SVT Models)

This part replaces:

  • Dorman 520-231
  • Dorman 520-232
  • Hollander 527-01413R
  • Hollander 512-00486L
  • Hollander 527-01414L
  • Hollander 512-00485R
  • Moog K80105
  • OE # YS4Z3280CB
  • OE # YS4Z3A130BA, YS4Z3A130CA
  • OE # YS4Z3A130CB, YS4Z3A130AA
  • OE # YS4Z 3079 BA
  • OE # YS4Z 3078 BA
  • OE # YS4Z3K661BB
  • OE # 5S4Z5K484AA
  • Moog K80406
  • Moog K80405
  • Moog K80066
  • Moog EV419
  • Moog ES3588
  • Moog ES3587
  • Reference Number BT-635
  • Monroe 181504
  • Monroe 181505
  • Monroe 171504
  • Monroe 171505
  • KYB SR4027
  • KYB SR4028
Part #: 1ASFK03088

Out of Stock

How-to Video:

(13:03 min)