Replaces

1999-01 Honda Odyssey Steering & Suspension Kit - 1ASFK04922

Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 6 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Lower Control Arms with Ball Joints
  • Kit Includes: (2) Front Sway Bar Links
  • Quantity: 6 Piece Set
  • Kit Includes: (2) Front Inner Tie Rods

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Removing the Wheel (1:05)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
    • If the wheel is frozen in place, kick the tire to loosen it
  2. step : Removing the Stabilizer Link (1:41)
    • Apply penetrating oil to the stabilizer link bolts
    • Attach an 18mm wrench to the back of the top stabilizer link bolt
    • Remove the top 18mm nut with a socket and ratchet
    • Pull out the top stabilizer link stud
    • Attach an 18mm wrench to the back of the bottom stabilizer link bolt
    • Remove the bottom 18mm nut with a second 18mm wrench
    • Pull out the stabilizer link
  3. step : Installing the New Stabilizer Link (3:30)
    • Push the lower stabilizer link stud into place
    • Push the upper stabilizer link stud into place
    • Start the two 18mm nuts
    • Tighten the nuts to between 55 - 60 foot-pounds of torque
  4. step : Reattaching the Wheel (4:05)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 95 - 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 18mm Socket

  • Wrenches - Metric

  • 18mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1999-2001 Honda Odyssey Steering & Suspension Kit 6 Piece Set

This part replaces:

  • Moog K90349
  • Dorman 521-352
  • Dorman 521-351
  • Hollander 512-58464R
  • Hollander 512-58464L
  • OE # 51350S0XA02
  • OE # 53010S0XA01
  • OE # 06513-S0X-A00, 51320S0XA02
  • OE # 51360S0XA02
  • Moog K620326
  • Moog K620325
  • Moog EV425
Part #: 1ASFK04922


Order must be placed by 4pm ET

How-to Video:

(04:51 min)