1AAHK00010-1994-97 Dodge Ram 1500 Front Passenger Side Wheel Hub Bearing & Axle Kit 2 Piece Set


1994-97 Dodge Ram 1500 Front Passenger Side Wheel Hub Bearing & Axle Kit 2 Piece Set


Part Details

  • Bearing Type: Tapered Roller Bearing
  • Quantity: 2 Piece Set

This part replaces:

  • Dorman 630-411
  • Hollander 447-02022R
  • Hollander 538-01302A
  • OE # 4746728
  • OE # 4746724
  • OE # 52008220
Save 30%
List: $323.95 Save: $97.00
Part 1AAHK00010
In Stock

Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

DIY Solutions
Brand #: HUB00001

Frequently bought together

Vehicle Fit
Warranty & Shipping
How-To & Tools

Part Details

  • Bearing Type:   Tapered Roller Bearing
  • Quantity:   2 Piece Set

What are Tapered Bearings and Why Use Them?

Tapered bearings are better than roller ball bearings at handling forces exerted on the bearing during cornering (known as axial load) in trucks and large cars. 

Roller ball bearings have spherical ball bearings between two straight rings (called races). Tapered bearings use tapered rollers shaped like flat-topped cones and two races angled from the outside to the inside of the bearing. The greater the angle, the more axial load the bearing can handle.

Your model came from the factory with tapered bearings. This type of bearing handles cornering forces better for trucks and large cars. Roller ball bearings work well for smaller cars, but replacing a tapered bearing with a roller ball bearing will result in increased wear and faster failure.


Precision Engineered

From the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.
100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water. Heavy duty grease resists high temperature, moisture, and reduces intense friction.

Direct Fit Replacement

Guaranteed to fit and function correctly for your specific application.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Mineral Oil, which is known to the State of California to cause cancer.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

  1. step : Removing the Wheel (1:18)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the 19mm lug nuts
    • Pull off the wheel
  2. step : Removing the Brakes (1:34)
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Remove 10mm allen head bolts from the brake caliper
    • Pull the caliper aside
    • Pull the rotor off
  3. step : Removing the Wheel Hub Assembly (3:17)
    • Remove the axle nut cotter pin
    • Remove the 1-3/4 in axle nut
    • Push in the axle
    • Remove the tie rod end cotter pin
    • Remove the tie rod end 21 mm castle nut
    • Hammer on the side of the knuckle to break the tie rod end loose
    • Support the tie rod
    • Remove the 12 point 9/16 hub assembly bolts
    • Rethread the bolts and hammer them to push the wheel hub assembly out
    • Remove the bolts hub assembly
    • Pry out the hub assembly as necessary
  4. step : Installing the Wheel Hub Assembly (11:35)
    • Clean the hub mounting surface of the wheel knuckle
    • Apply anti-seize grease to the mounting surface and axle splines
    • Clean the mounting surface of the backing plate as necessary
    • Slide the hub assembly bolts into the knuckle
    • Set the backing plate on the hub assembly bolts
    • Set the hub assembly into the knuckle aligned with the bolts
    • Install the hub assembly bolts
    • Torque the 12 point 9/16 hub assembly bolts to 125 ft-lb
    • Insert the tie rod end into the knuckle
    • Install the 21 mm tie rod castle nut
    • Torque the 21 mm tie rod castle nut to 65 ft-lb, then continue tightening the nut to align the cotter pin hole if necessary
    • Install the tie rod end cotter pin and peen it over
    • Insert a pry bar through the U joint
    • Install the axle washer and nut
    • Torque the 1-3/4 axle nut to 175 ft-lbs and continue tightening to align the cotter pin hole if necessary
    • Install the cotter pin and peen it over
    • Apply anti-seize to the wheel hub surface
  5. step : Installing the Brakes (18:02)
    • Install the brake rotor onto the wheel studs
    • Secure the rotor temporarily with a lug nut
    • Set the brake caliper in position
    • Install the 10 mm allen slider bolts
    • Torque the slider bolts to 38 ft-lb
    • Remove the lug nut
  6. step : Installing the Wheel (19:48)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the 19mm lug nuts preliminarily
    • Lower the vehicle partially to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Hammer
  • Wire Brush

  • Hex Wrenches

  • 10mm Hex Socket

  • Materials, Fluids, and Supplies

  • Brake Parts Cleaner
  • Anti-Seize Grease
  • Brake Grease

  • Ratchets & Related

  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 21mm Socket

  • Sockets - SAE

  • 1-3/4 in Socket
  • 9/16 in 12-Point Socket

Need help? Ask one of our Auto Experts
Need help? Ask one of our Auto Experts
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.

Fits the following Makes:

Year Make Model Description
1994-1997Dodge Ram 1500 Truck Dodge Ram 1500 Truck 4 Wheel Drive with 4 Wheel ABS Brakes Front Passenger Side Wheel Hub Bearing & Axle Kit 2 Piece Set

Part Interchange

Brand Label Part Number
Chicago Rawhide BR930256
Chrysler 52008220
DIY Solutions HUB00001
DIY Solutions ADS00202
Dodge 4746728
Dodge 5015136AB
Dorman - OE Solutions 630-411
Drive Tech America NT515006
GMB 725-0011
Green Ball WH596
Hollander 447-02022R
MOOG Hub Assemblies 515006
Mevotech H515006
Mopar V2508220AA
Raybestos 715006
Raybestos Brakes 715006
SKF BTD-5108
SKF BR930256
Timken 515006

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

DIY Solutions
Brand #: HUB00001
Product Reviews
There are no reviews for this item.
Customer service


Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET

1994-97 Dodge Ram 1500 Front Passenger Side Wheel Hub Bearing & Axle Kit 2 Piece Set-1AAHK00010 does not fit your:

Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a vehicle with these options.