Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Direct Fit - No vehicle or wiring modification necessary
DOT, SAE, and FMVSS Compliant - Meets on-road use regulations
Matching set for a restored look
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
The bulbs are for testing and not covered under our warranty. Our warranty applies to the light assembly only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How To Replace Taillight 1993-2010 Ford Ranger
How to Replace Tail Light 1993-97 Ford Ranger
Created on:
Tools used
Phillips Head Screwdriver
1. Removing the Taillight Assembly
Remove the four screws securing the taillight.
Pull the taillight out.
Twist out the lower socket.
Push in the thumb and pull off the connector.
Twist out the upper socket.
Bulbs can be serviced at this time.
2. Replacing the Taillight Assembly
Twist in the upper socket.
Reconnect the harness.
Twist in the lower socket.
Line up the taillight assembly.
Push it into place.
Replace the four screws.
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet.
Hi. I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money preparing and maintaining your vehicle. I'm going to use my 20 plus years' experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correct is going to save you time and money .Thank you. Enjoy the video.
In this video we're going to replace the taillights on this 2004 Ford Ranger. This is basically the same procedure for a 1993 on up. All you need is a Phillips screwdriver.
This is a 2004 Ford Ranger, the same as many years of Ranger. The taillight replacement is pretty easy. There are four screws, one, two and then on the outside three and four. Remove those. Once you have those screws out, it pulls off. The lower one you can turn and pull it out. This upper one you have to actually press this thumb tab and remove the connector. Then this part can come out and you can service it.
You can see the original light is from 1A Auto. It's all the same. It's a little nicer and shinier. Everything's going to mount the same and all that. This one's in good shape. We're going to put it back in. Obviously to put it in it's reversing the procedure. There's actually a little tab that goes in the slot right here. You want to tighten them but not too tight. They just need to be firm and snug. There you go.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free. 888-844-3393. We're the company that's here for you on the internet and in person.
Tools used
Phillips Head Screwdriver
1. Removing the Taillight
Remove the four Phillips head screws from the taillight
Pull out the taillight
2. Servicing the Taillight Bulbs
Twist the bulb sockets counterclockwise and out
Pull the bulbs out of the sockets
Push the new bulbs into the sockets
3. Installing the New Taillight
Twist the bulb sockets clockwise into the new taillight, from bottom to top
Push the new taillight into place
Insert the four Phillips screws into the taillight
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to service the tail light on this '96 Ranger, same as a '93 to '97. We're going to show you both replacing the whole assembly, and just changing the bulbs as well, and the only tool you'll need is a Phillips screwdriver.
To replace one of these tail lights on a Ranger, there are four screws. You can see there are two Phillips screws out here, and then also two Phillips screws right in here. I'll speed up as we just remove those two screws from the outboard side of the tail light. Sometimes these inside screws can be a little sticky so you want to make sure you can get some good leverage on the screw driver. Once those are out, the light comes right out.
If you're just looking to change bulbs, all these just turn counterclockwise. The bulb comes straight out of the socket, and back in.
Here's the original and a new one from 1A Auto. Obviously, my original is in pretty good shape, but maybe you backed into something and broke a tail light, or something like that. The new one from 1A Auto is going to go in, just the same as the original one. Push them in. Lock them in clockwise. It's better to do the bottom one first, push it in, and lock it in. Take the middle one. I'm just going to make sure we get all the right ones here lined up correctly. Push it in, lock it in clockwise, put the light into place, and start my two inside ones, first. Now, on these outer ones, you can see right here is the clip where it goes into, so you can put your screw in, and make sure the screw goes into that clip. Start the top one a little bit, and make sure that bottom one goes in. Speed it up here. You want to be careful not to tighten these screws up too much because you could crack your tail light lens.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
FR252-U000R
In Stock
Product Reviews
Loading reviews
4.67/ 5.03
3 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
2
1
0
0
0
RANGER PICKUP TAIL LIGHT
J
January 31, 2020
The left tail light for my 1993 Ford Ranger fit perfect with no problems. Very helpful with the video to watch what to do too.
tail light
R
November 16, 2020
we were satisfied with the purchase and the prompt delivery.
It is not the first time we ordered from 1A Auto.
Purchased a rear tail light lense for 96 Ford Ranger
F
January 1, 2021
Fits well. Would recommend 1A to anyone. Other purchases that worked out well...headlights for Subaru and headlights for the same Ranger. All seems to be quality merchandise.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.