1ASFK03877-1993-95 Jeep Grand Cherokee Steering & Suspension Kit 11 Piece Set

Replaces

1993-95 Jeep Grand Cherokee Steering & Suspension Kit 11 Piece Set TRQ PSA59447

1ASFK03877

Part Details

  • Kit Includes: (2) Front Lower Ball Joints
  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (1) Track Bar
  • Quantity: 11 Piece Set
  • Kit Includes: (2) Front Sway Bar Links
  • Kit Includes: (2) Front Upper Ball Joints
  • Kit Includes: (2) Front Inner Tie Rods

This part replaces:

  • Moog K7208T
  • Moog K3161T
  • Moog DS1235
  • Moog ES3096L
  • Moog K3174
  • Moog DS1310
  • Moog DS1312
  • Hollander AXK3134T
  • OE # 52037849
  • OE # 52007118
  • OE # 52005739
  • OE # 52037996
  • OE # 52037994
FREE SAME DAY SHIPPING
Save 28%
List: $205.95 Save: $58.00
Only 7 left in stock
Part 1ASFK03877
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

TRQ
Brand #: PSA59447
Description
Vehicle Fit
Warranty & Shipping
How-To & Tools
Q&A

Part Details

  • Quantity:   11 Piece Set
  • Kit Includes:
      (2) Front Lower Ball Joints
      (2) Front Outer Tie Rods
      (1) Track Bar
      (2) Front Sway Bar Links
      (2) Front Upper Ball Joints
      (2) Front Inner Tie Rods

Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as an 11 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

  1. step : Removing the Wheel (1:03)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Straighten the cotter pin on the axle nut with needle nose pliers
    • Remove the cap and washer from the axle nut
    • Loosen the axle nut with a 36mm socket and breaker bar
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Rotor (2:29)
    • Remove 13mm bolts from the brake caliper
    • Pull the caliper aside and secure it out of the way with a bungee chord
    • Pull the rotor off
  3. step : Removing the Hub (3:17)
    • Spray rust penetrant around the contact points of the hub
    • Remove the three 13mm 12-point bolts from the hub
    • Pry off the washer from the axle (if you have one) with a pick
    • Tap the axle in with a hammer to free the splines from the hub
    • Tap the hub out of the spindle with a hammer
    • Remove the hub and dust shield
  4. step : Loosening the Tie Rod (4:56)
    • Remove the cotter pin from the tie rod castle nut with a pair of pliers
    • Remove the 19mm castle nut from the tie rod
    • Hit the edge of the spindle to release the stud
    • Release the tie rode from the spindle
  5. step : Removing the Lower and Upper Ball Joint (6:08)
    • Remove the cotter pins from the upper and lower ball joints
    • If the cotter pin breaker or gets stuck, punch the pin through with a punch and hammer
    • Remove the axle shaft from the housing
    • Insert rags or a glove to stop axle fluid from leaking
    • Remove the two 22mm castle nuts from the ball joints
    • Insert a pick fork between the upper ball joint and the spindle to release the ball joint
    • If needed, hit the bottom to release the spindle from the axle
    • Remove the upper ball joint with a ball joint press
    • Repeat the process for the lower ball joint
  6. step : Installing the Lower and Upper Ball Joint (11:36)
    • Remove the boots from the ball joints
    • Press the upper ball joint into the spindle with the ball joint press until it bottoms out into the slot on the axle
    • Insert the boot to the upper ball joint
    • Press the lower ball joint into the spindle with the ball joint press until it bottoms out into the slot on the axle
    • Insert the boot to the lower ball joint
    • Hand-tighten the lower ball joint castle nut
    • Hand-tighten the upper ball joint castle nut
    • Tighten the lower ball joint castle nut with a 32mm socket and ratchet
    • Tighten the upper ball joint castle nut with a 22mm socket and ratchet
    • Torque the upper ball joint nut to 75 foot-pounds
    • Torque the upper ball joint nut to 80 foot-pounds
    • Install the lower cotter pin with the longer end facing down over the stud
    • Cut the shorter leg off
    • Install the upper cotter pin with the longer end facing down over the stud
    • Cut the shorter leg off
    • Tighten the upper ball joint grease fitting with a 7mm wrench
    • Add grease to the ball joint until the boot swells without popping off the joint
    • Remove the rags blocking the axle fluid
    • Insert the axle into the differential
  7. step : Reinstalling the Tie Rod (15:41)
    • Insert the tie rod into the spindle
    • Tighten the 19mm castle nut
    • Torque the tie rod nut to 35 foot-pounds
    • Insert the new cotter pin into the tie rod
    • Bend the longer leg over the top of the stud
    • Cut the shorter leg
  8. step : Installing the Hub (16:37)
    • Insert the dust shield into place
    • Insert the hub into place
    • Tighten the 12-point 13mm bolts
    • Torque the hub bolts to 75 foot-pounds
  9. step : Installing the Rotor (17:27)
    • Insert the rotor onto the hub
    • Press the caliper onto the rotor
    • Tighten the two 13mm bolts to the caliper
    • Torque the caliper mounting bolts to 20 foot-pounds
  10. step : Reattaching the Wheel (18:07)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 110 foot-pounds in a crossing or star pattern
    • Torque the axle nut to 175 foot-pounds
    • Insert the axle nut cap into place
    • Insert a new cotter pin into place
    • Turn each end of the cotter pin to opposite sides of the nut

Tools needed for replacement:

    General Tools

  • Center Punch
  • Hammer
  • Pick

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Bungee Cord

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 19mm Socket
  • 13mm Socket
  • 36mm Socket
  • 22mm Socket

  • Specialty Tools

  • Ball Joint Press
  • Pickle Fork
  • Grease Gun

  • Wrenches - Metric

  • 7mm Wrench

Need help? Ask one of our Auto Experts
Need help? Ask one of our Auto Experts
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Will this fit in the 4.0 L engine?
Richard T May 18, 2018
Not the kit I bought. My ZJ is a V8
J D August 10, 2020

Fits the following Makes:

Year Make Model Description
1993-1995Jeep Grand Cherokee Jeep Grand Cherokee V8 5.2L 4 Wheel Drive Steering & Suspension Kit 11 Piece Set

Part Interchange

Brand Label Part Number
Chrysler 52037849
Chrysler 52037994
Chrysler 52037996
Chrysler 52007118
Chrysler 52005739
DIY Solutions SUS00140
DIY Solutions SUS07723
DIY Solutions SUS00141
DIY Solutions SUS06694
DIY Solutions SUS07722
DIY Solutions SUS06695
DIY Solutions SUS07437
MOOG DS1312
MOOG ES3096L
MOOG K3161T
MOOG K3174
MOOG DS1235
MOOG DS1310
MOOG K3134T
MOOG Chassis Products K3161T
MOOG Chassis Products K3134T
MOOG Chassis Products ES3096L
MOOG Chassis Products DS1235
MOOG Chassis Products K3174
MOOG Chassis Products DS1312
MOOG Chassis Products DS1310

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

FREE SAME DAY SHIPPING
TRQ
Brand #: PSA59447
Product Reviews
4.12/ 5.0
8 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
5
1
1
0
1
JEEP CHEROKEE LIMITED FRONT END
First, the price was great, the shipping was fast. The parts were an exact replacement, easiest front end i have ever done. All the parts were perfect, no burs, no bad seals, i mean plug and play, if you can imagine that. HIGHLY RECOMMEND TO EVERYONE.
July 23, 2018
Fast
Parts came faster than expected. Prices are great and site is easy to navigate. Recommending them to others
October 20, 2018
terrible
this product is terrible purchased this kit about 3-4 months ago package arrived 5 of the ballpoints on the tie rods/regular ball joints were broken (sleeve wasn’t connected to the ball joint) called and they said they’d send me replacements the replacements arrived and all of them were broken as well same problem called and asked for a refund and they refused to refund me without sending the parts back told me they’d send me the shipping labels for the return still have not received the paperwork terrible service terrible parts WOULD NOT RECOMMEND
January 21, 2019
Purchase
Great product, price and in time delivery!!! Will buy more products here in the future.
March 29, 2019
Review
I love this company but had a lot of issues with my products because of the carrier UPS. 1A Auto was there to help and fix any problem I had. Thank you 1A Auto
June 17, 2019
Great product
Excellent replacement and exact fit no issues. There was a slight change on the ball joints when I called to find out the rep was not sure but found out who did know. I appreate tellingme youbdont know but I will find out then making something up. So I ended up ordering more parts
July 2, 2019
Happy
Happy with my parts
August 9, 2019
Got everything needed to rebuild right
This kit is pretty good. Got all the parts needed to rebuild the steering components. The fitment was good. The only complaint I have is that the grease boots on a couple items seemed a little loose and there are no grease fitments on any of the parts. But the front end of the 1995 ZJ feels good and rides smooth now. Overall this is a good product and shipping was faster than expected. It’s definitely a buy and I will shop here again.
August 10, 2020
Customer service

877-844-3393

Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET


1993-95 Jeep Grand Cherokee Steering & Suspension Kit 11 Piece Set TRQ PSA59447-1ASFK03877 does not fit your:


Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a vehicle with these options.