Replaces

1993-11 Ford Ranger Door Handle Latch Cable - 1ADMX00168

This replacement door handle cable is just what you need to get your vehicle in good working form again!

Specifications

  • Fits Driver or Passenger side door
  • Replaces dealer part numbers: F37Z-10221A00A, F37Z10221A00A
  • Reinforced from the original design for better durability
  • Direct replacement for original cable

This part is a direct bolt on and is built to strict quality control standards. It is a great replacement and has substantial cost savings over a dealer unit.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Door Panel (1:05)
    • Remove the two Phillips head screws in the door pull
    • Pull the door handle panel out
    • Disconnect the wiring harnesses
    • Remove the Phillips head screw beneath the door handle
    • Remove the Phillips head screw in the bottom left corner
    • Lift the door panel up and off
  2. step : Removing the Interior Door Handle (2:28)
    • Remove the weathershield carefully
    • Drill out the rivet from the door handle
    • Pinch and push the connectors on the door cable through the door
    • Pull the door handle back and out of the door
    • Peel back the rubber cover
    • Pop the cable clip out of the door handle
    • Rotate the handle off of the cable
  3. step : Removing the Interior Door Latch Cable (4:03)
    • Push the connector from the cable out of the door
    • Remove the cover from the cable over the lock actuator
    • Slide the cable toward the outer portion of the door to release it
    • Pull back on the cable to lock the arm and hold it there with a flat blade screwdriver
    • Pull the ball end up and out
    • Remove the cable
  4. step : Installing the Interior Door Latch Cable (6:02)
    • Send the cable through the latch
    • Pull the latch back
    • Hook the cable into the latch
    • Clip the cable end into its slot with a pair of pliers
    • Reinstall the plastic cover
  5. step : Installing the Interior Door Handle (6:37)
    • If the clips broke, zip-tie the cable into place
    • Connect the cable to the handle
    • Clip the cable into the door handle
    • Press on the rubber cover
    • Press the door handle into the door
    • Tighten a new bolt to the door handle
  6. step : Installing the Door Panel (8:30)
    • Realign the weathershield
    • Insert the door panel into its slots
    • Press the door panel into place
    • Tighten the Phillips screw in the bottom left corner
    • Tighten the Phillips screw beneath the door handle
    • Connect the wiring harnesses to the door handle panel
    • Press the door handle panel into place
    • Tighten the two Phillips head screws to the door pull

Tools needed for replacement:

    Drills, Drill Bits & Related

  • Drill
  • Drill Bit Set

  • Materials, Fluids, and Supplies

  • Wire Ties

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Specialty Tools

  • Rivet Gun & Rivets

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 2 answers
Will this cable work in the extended cab of a Ford Ranger? I need to replace both the upper and lower cables on both sides of the extended cab.
James M on May 1, 2018
BEST ANSWER: This part is specific to vehicles with a particular set of options. We will need more information about your vehicle to confirm the fit. Please feel free to call our customer service department for clarification @ 888-844-3393.

Vehicle Fit

  • 1993-2011 Ford Ranger Interior Front Door Handle Latch Cable

This part replaces:

  • OE # F37Z10221A00A
Part #: 1ADMX00168

Ships Same Day for orders placed by 4 P.M. ET

How-to Video:

(10:46 min)