Replaces

2002-2005 Chevy Trailblazer Front Wheel Hub & Bearing Pair with CERAMIC Brake Pads & Rotors Set

Part Details

  • Front / Rear Location: Front

  • New

This front wheel bearing/hub assembly, brake rotor, & brake pad set is just what you need to get your vehicle in good stopping order again!

Brake Pad Specifications:

  • Fits FRONT Rotors
  • 4 Piece Brake Pad Set
  • No core charge
  • Includes shims
  • Ceramic Enhanced Disc Brake Pads

Brake Rotor Specifications:

  • Comes as a PAIR
    • Fits LH (Driver Side) & RH (Passenger Side) FRONT
  • Replaces dealer part numbers: 19181002
  • Fit 6 Stud Wheels
  • 11.9" Diameter Vented Rotors

Wheel Bearing & Hub Assembly Specifications:

  • Comes as a PAIR
    • Fits both the LH (Driver Side) & RH (Passenger Side) FRONT
  • Replaces dealer part numbers: 12413037, 15130858
  • Includes lug nut studs already installed, ABS Sensors, and ABS Sensor Wire Harnesses
  • 3 Bolt Flanges
  • Fit both 2WD & 4WD Models

This wheel bearing/hub assembly, brake rotor, & brake pad set makes great replacements and has good value over the price of dealer parts.

2 Year Warranty

This item is backed by a 2 Year Warranty. In the event this item should fail during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Step 1: Remove the wheel and tire (1:18 in the video)
    • Raise and secure the vehicle.
    • Remove the lug nuts and then the wheel.
  2. Step 2: Remove Caliper (2:07 in the video)
    • Turn wheels all the way in the opposite direction of the side you are working on.
    • Use your 13mm socket wrench to remove the caliper bolts.
    • Use a wire tie to help prevent stress on the caliper.
    • Use your 18mm socket to remove the brackets.
  3. Step 3: Remove brake disk (4:13 in the video)
    • Take care not to touch the disk, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
  4. Step 4: Remove Hub (4:42 in the video)
    • Use a 35mm socket to remove the hub nut.
    • Give the axle a slight tap with a hammer to loosen it.
    • Remove the 3 bolts securing the hub using your 18mm socket and extension and ratchet or breaker bar.
    • You can use penetrating oil to help.
    • Disconnect your ABS sensor.
    • Use a rubber mallet to break your hub free, and work around the flange with the hammer to pull it off.
    • Remove the hub and shield.
    • Clean up any corrosion with a wire brush.
  5. Step 5: Install new hub (9:10 in the video)
    • Use some penetrating oil to prep the knuckle for the new hub.
    • Put the three 18 mm bolts in place and tighten the nuts to 90 ft lbs.
    • Reinstall the ABS harness.
    • Tighten but don't torque the lug nut.
  6. Step 6: Put brakes and wheel back on (11:50 in the video)
    • Remember to replace the lug nuts on in a star pattern.
    • Lug nuts tighten to 100-120 ft lbs
    • Hub nut is 103 ft lbs.
    • Make sure to check your brakes and steering before driving again.
    • Make sure to pump the brakes and seat your rotors.

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Rust Penetrant
  • Wire Ties

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 18mm Socket
  • 19mm Socket
  • 35mm Socket

  • Specialty Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Large C-Clamp
  • Rubber Mallet
  • Wire Brush

How-to Video:

(13:45 min)

Tools List:

    Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Rust Penetrant
  • Wire Ties

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 18mm Socket
  • 19mm Socket
  • 35mm Socket

  • Specialty Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Large C-Clamp
  • Rubber Mallet
  • Wire Brush




Vehicle Fit

  • 2004-2005 Buick Rainier Front Wheel Hub & Bearing Pair with CERAMIC Brake Pads & Rotors Set for L6 4.2L Models
  • 2002-2005 Chevy Trailblazer Front Wheel Hub & Bearing Pair with CERAMIC Brake Pads & Rotors Set
  • 2002-2004 GMC Envoy Front Wheel Hub & Bearing Pair with CERAMIC Brake Pads & Rotors Set
  • 2005 GMC Envoy Front Wheel Hub & Bearing Pair with CERAMIC Brake Pads & Rotors Set for L6 4.2L Models
  • 2003-2005 Isuzu Ascender Front Wheel Hub & Bearing Pair with CERAMIC Brake Pads & Rotors Set for L6 4.2L Models
  • 2002-2004 Olds Bravada Front Wheel Hub & Bearing Pair with CERAMIC Brake Pads & Rotors Set
$155.45
Part #: 1ABMS00022

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est