Replaces

1999-2005 VW Jetta O2 Oxygen Sensor Downstream for L4 2.0L

Part Details

  • Location: Downstream

This part replaces:

  • OE # 06A906262BG
  • STANDARD MOTOR PRODUCTS SG1170

  • New

Specifications:

  • Direct Fit
    • Correct Connector No cutting or splicing
      • may appear different from original however will install and function correctly
    • Correct wire length (15 Inches)
  • Downstream Sensor as listed per applications
  • Heated
  • 4 wire configuration
  • 4 terminal configuration
  • Replaces dealer part numbers: 06A906262BG, 06A 906262 BG
  • Built and tested to strict quality control standards

Note: For clarification purposes:

  • Upstream location is between the catalytic converter and the engine
  • Downstream location is between the catalytic converter and the tailpipe

If you have a bad O2 sensor causing your vehicle to run poorly or fail an emission test then this is the part for you.

Note:  You may be required to reset the vehicle’s computer after installation of this part.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Downstream Oxygen Sensor (0:43 in the video)
    • Raise and secure the vehicle
    • Unbutton the O2 sensor insulation sleeve and pull it off
    • Remove the sensor wire from its bracket
    • Remove the two 10mm nuts from the sensor wire box
    • Pull the downstream O2 sensor wiring harness out of the box
    • Disconnect the downstream O2 sensor wiring harness
    • Put the O2 sensor tool onto the sensor wire and slide it onto the sensor
    • Put a 3/8 inch ratchet into the O2 sensor tool
    • Loosen the sensor until it can be twisted off by hand
    • Twist off the sensor by hand
  2. Installing the New Downstream Oxygen Sensor (2:28 in the video)
    • Twist the new O2 sensor into place
    • Tighten the new sensor with the O2 sensor tool and 3/8 inch ratchet
    • Button the insulation sleeve around the sensor wire
    • Clip the new sensor wire into its bracket
    • Reconnect the downstream O2 sensor wiring harness
    • Push the downstream O2 sensor wiring harness into the wiring harness box
    • Push the wiring harness box into place
    • Fasten the two 10mm nuts onto the wiring harness box
    • Lower the vehicle to the ground

Tools needed for replacement:

    Ratchets & Related

  • 3/8 inch drive ratchet
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Specialty Tools

  • Floor Jack
  • Jack Stands
  • O2 Sensor Socket

How-to Video:

(04:10 min)

Tools List:

    Ratchets & Related

  • 3/8 inch drive ratchet
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Specialty Tools

  • Floor Jack
  • Jack Stands
  • O2 Sensor Socket



This part replaces:

  • OE # 06A906262BG
  • STANDARD MOTOR PRODUCTS SG1170

Vehicle Fit

  • 2001-2005 VW Beetle O2 Oxygen Sensor Downstream for L4 2.0L (Engine ID AVH) (Engine ID AZG)
  • 2006-2010 VW Beetle Downstream Rear O2 Oxygen Sensor for L5 2.5L
  • 2000-2006 VW Golf O2 Oxygen Sensor Downstream for L4 2.0L
  • 1999-2005 VW Jetta O2 Oxygen Sensor Downstream for L4 2.0L
$63.95
Save 59%
List: $157.17 Save: $93.22
Part #: 1AEOS00099

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est