Replaces

1990-1998 Jeep Cherokee Front Wheel Bearing & Hub Assembly 4 Wheel Drive

This part replaces:

  • OE # 53007449
  • OE # 53007449AB
  • Hollander 538-01267

  • New

Specifications:

  • Correct for models with Composite Vented Rotor
  • Fits RH or LH FRONT
  • 3 bolt triangular flange
  • Replaces dealer part numbers: 53007449AB, 53007449
  • Direct replacement
  • Fits 5 Lug Wheel
  • Built to strict quality control standards

Note: If you have any questions about this fitting your application, please call your local dealer with the above part number.

 

Quality

  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both Bizrate.com and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hub & bearings are all tested prior to shipping.

Fit Guaranteed

  • This hub & bearing will install just as your original does. You can use your existing hardware.
  • Save time and money with this direct fit hub bearing assembly. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.

Value

  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.

2 Year Warranty

This item is backed by a 2 Year Warranty. In the event this item should fail during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Wheel (0:51)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Straighten the cotter pin on the axle nut with needle nose pliers
    • Remove the cap and washer from the axle nut
    • Loosen the axle nut with a 36mm socket and breaker bar
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. Removing the Brake Rotor (2:18)
    • Remove 13mm bolts from the brake caliper
    • Pull the caliper aside and secure it out of the way with a bungee chord
    • Pull the rotor off
  3. Removing the Hub (3:10)
    • Spray rust penetrant around the contact points of the hub
    • Remove the three 13mm 12-point bolts from the hub
    • Pry off the washer from the axle (if you have one) with a pick
    • Tap the axle in with a hammer to free the splines from the hub
    • Tap the hub out of the spindle with a hammer
    • Remove the hub and dust shield
  4. Installing the Hub (5:55)
    • Insert the dust shield into place
    • Insert the hub into place
    • Tighten the 12-point 13mm bolts
    • Torque the hub bolts to 75 foot-pounds
  5. Installing the Rotor (6:49)
    • Insert the rotor onto the hub
    • Press the caliper onto the rotor
    • Tighten the two 13mm bolts to the caliper
    • Torque the caliper mounting bolts to 20 foot-pounds
  6. Reattaching the Wheel (7:28)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 110 foot-pounds in a crossing or star pattern
    • Torque the axle nut to 175 foot-pounds
    • Insert the axle nut cap into place
    • Insert a new cotter pin into place
    • Turn each end of the cotter pin to opposite sides of the nut

Tools needed for replacement:

    General Tools

  • Hammer
  • Pick

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Bungee Cord

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 19mm Socket
  • 13mm Socket
  • 36mm Socket

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
excellent product works good no problems.
April 18, 2010
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(08:55 min)

Tools List:

    General Tools

  • Hammer
  • Pick

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Bungee Cord

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 19mm Socket
  • 13mm Socket
  • 36mm Socket



This part replaces:

  • OE # 53007449
  • OE # 53007449AB
  • Hollander 538-01267

Vehicle Fit

  • 1990-1998 Jeep Cherokee Front Wheel Bearing & Hub Assembly 4 Wheel Drive
  • 1990-1992 Jeep Comanche (MJ) Front Wheel Bearing & Hub Assembly 4 Wheel Drive
  • 1993-1998 Jeep Grand Cherokee Front Wheel Bearing & Hub Assembly
  • 1993 Jeep Grand Wagoneer Front Wheel Bearing & Hub Assembly
  • 1990 Jeep Wagoneer Front Wheel Bearing & Hub Assembly
  • 1990-1995 Jeep Wrangler Front Wheel Bearing & Hub Assembly
  • 1997-1998 Jeep Wrangler Front Wheel Bearing & Hub Assembly
$ 45.95
Save 83%
List: $267.00 Save: $221.05
Part #: 1ASHF00011

Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

1A Auto Parts

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY M-F
For Orders Placed By 5pm Est