Replaces

2000-2003 Chevy Monte Carlo Radiator Dual Cooling Fan Assembly

This part replaces:

  • HOLLANDER 674-00818A
  • DORMAN 620-616 Branded
  • PARTSLINK GM3115122 / GM3117104
  • OE # 89022512

  • New

Our aftermarket cooling fan assemblies are some of the highest quality replacements on the market! This radiator fan assembly is a complete, ready to bolt on, direct replacement part.

Specifications:

  • New, not rebuilt, electric motor
  • Replaces dealer part number: 89022512
  • Geometrically designed plastic blades for optimal circulation and uniform balance
  • Plastic shroud designed to ensure structural integrity and endurance for maximum performance
  • Performance tested
  • Replaces original assemblies that are melted or worn out
  • Comes with proper plug for trouble free installation

Now you can buy a high quality cooling fan assembly that is built to strict quality control standards. It is a great replacement and has substantial cost savings over a dealer unit.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Engine Mounts (0:43 in the video)
    • Remove the eight 13mm bolts from the engine mounts
    • Loosen the 13mm bolt from the support bar
    • Push the support bar to the side
    • Lift up the two engine mounts
  2. Removing the Air Intake Box (1:15 in the video)
    • Disconnect the mass airflow sensor harness
    • Loosen the air intake hose clamps with a flat blade screwdriver
    • Pull the intake hose free
    • Loosen the two 8mm bolts from the air box
    • Pull the air intake box forward, up, and out
    • Pull the back of the air intake box out
  3. Removing the Radiator Fan (2:05 in the video)
    • Remove the 10mm bolt on either side of the radiator fan
    • Remove the 10mm bolt and mount on either upper corner of the radiator fan
    • Disconnect the two fan wiring harnesses
    • Unclip the series of clips along the fan harness with a flat blade screwdriver
    • Clip the wire tie and pull the vacuum hose free
    • Clip the hose clamp with pliers and pull the radiator hose free
    • Tuck the radiator hose behind the engine mount
    • Lift the radiator cooling fan up and out
  4. Installing the New Radiator Fan (4:25 in the video)
    • Line up the two tabs on the radiator fan with the two slots
    • Place the radiator fan into its slots
    • Replace and tighten the 10mm bolts and the radiator mounts
    • Replace and tighten the lower 10mm bolts on the radiator fan
    • Push the tab on the back of the clips from the old radiator fan and remove them
    • Clip the clips into the new radiator fan
    • Re-clip the harness into the new clips
    • Place the outer air box pins into the rubber grommets
    • Re-clip the larger wire clip and harness back into place
    • Connect the two fan wiring harnesses
    • Push the teeth together on the radiator hose clamp
    • Push the radiator hose into place
  5. Installing the Air Intake Hose (7:40 in the video)
    • Remove the mass airflow sensor
    • Remove the small ring off the sensor and place it on the intake box
    • Push the tab on the ring between the two posts on the box
    • Push the mass inflow sensor onto the intake hose
    • Lower the intake box and attach it to the sensor
    • Tighten the two hose clamps
    • Reconnect the mass air flow sensor harness
    • Line up the air intake box
    • Tighten the two 8mm bolts on the air intake box
  6. Installing the Engine Mount (9:11 in the video)
    • Pull the engine mounts down
    • Pull the engine forward and align the engine mounts
    • Replace and tighten the eight 13mm bolts on the engine mounts
    • Tighten the 13mm bolt on the support bar
    • Reconnect the vacuum hose and tighten it with a wire tie

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Wire Cutters

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 13mm Socket
  • 8mm Socket

How-to Video:

(10:17 min)

Tools List:

    Materials, Fluids, and Supplies

  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Wire Cutters

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 13mm Socket
  • 8mm Socket



This part replaces:

  • HOLLANDER 674-00818A
  • DORMAN 620-616 Branded
  • PARTSLINK GM3115122 / GM3117104
  • OE # 89022512

Vehicle Fit

  • 2000-2003 Chevy Impala Radiator Dual Cooling Fan Assembly (without Heavy Duty Cooling)
  • 2000-2003 Chevy Monte Carlo Radiator Dual Cooling Fan Assembly
$105.45
Part #: 1ARFA00089

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est