Menu

1A Auto Video Library
Our how-to videos have helped repair over 100 million vehicles

How to Replace Speed Sensor Automatic Transmission 97-11 Ford Ranger

Share on:
  1. step : Removing the Output Speed Sensor (1:02)
    • Disconnect the wiring harness
    • Remove the T30 Torx screw from the sensor
    • Remove the sensor
  2. step : Installing the Output Speed Sensor (2:47)
    • Lubricate the O-ring with the correct transmission fluid or rust penetrant
    • Insert the sensor into the transmission
    • Tighten the T30 Torx screw
    • Connect the wiring harness

Hi, I'm Mike from 1AAuto. We've been selling auto parts for over 30 years! We're dedicated to delivering quality auto parts, expert customer service, and fast and free shipping, all backed by our 100% satisfaction guarantee. We've created thousands of videos to help you install our parts with confidence. That saves you time and money, so visit us at 1AAuto.com, your trusted source for quality auto parts.

In this video, we're going to be working with our 2001 Ford Ranger 4.0-liter, 5-speed, automatic transmission. We're going to be showing you how to remove and replace your output speed sensor on your transmission. Again, this is specific to the 5-speed.

If you like this video, please click Subscribe. We have a ton more information on this truck, as well as many other makes and models. If you need this part for your vehicle, you can follow the link down in the description over to 1AAuto.com.

Here are the items you'll need for this repair: T-30 Torx bit, ratchet, flat blade screwdriver, rust penetrant, and automatic transmission fluid

Your transmission output speed sensor or OSS is located at the backside of the transmission. The top on the driver's side, right where it bolts to the transfer case on these 4-wheel drive models. We'll start by removing the electrical connector. Remove the T30 Torx screw on the back of the sensor with a T30 Torx bit and a ratchet. These also have a 10mm hex on the outside, but ours has a good bit of rust and corrosion on it. We weren't able to get it to turn with the socket. Then you should be able to grab the sensor and work it side to side a little, to help release it from the case. However, you may need to use a long flat blade screwdriver to try to pry up on it.

Here we have our old output speed sensor that we removed from our vehicle and our new part from 1AAuto.com. As you can see, these parts have the same sensor on the end. The same two-pin electrical connector and the same single point mounting location on the side here. Our old one is actually cracked a little bit. Also comes with a new O-ring on it to seal it into the case. There's no gasket or sealant needed required here. If you have a check engine light or another issue related to your output speed sensor on your automatic transmission, this new part from 1A Auto is going to go in direct fit, just like your original equipment and fix you up right.

Lubricate the O-ring on the new sensor with some penetrating oil or the proper automatic transmission fluid for the vehicle. Seat it in fully. Be sure to feel for where the opening is for the bolt to keep it aligned. Reinstall your T30 Torx screw into the back of the speed sensor with a T30 Torx socket. Just be sure to watch it and make sure that the whole sensor is in properly and that you aren't just pulling one side down, otherwise you risk breaking the sensor. If yours looks like it's going in crooked, you may need to apply a little more lubrication to it. Once the sensor's reinstalled, reinstall your electrical connector and you're good to go.

Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Rust Penetrant
  • Transmission Fluid

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Star Drivers & Sockets

  • T30 Driver

2001 - 2005  Ford  Explorer Sport Trac
1997 - 2002  Ford  Explorer
1998 - 2007  Mazda  B4000 Truck
1997 - 2011  Ford  Ranger
1998 - 2007  Mazda  B3000 Truck

Speed Sensor

Ford Mazda Speed Sensor Standard Motor Products

This part replaces:

  • Standard Motor Products SC370
  • OE # F7RZ7H103BA
  • OE # DY1206
Search Videos
Go To Top


Same Day Shipping

Orders ship same day when ordered by 2pm ET. Need your part faster? Choose expedited shipping at checkout.


Guaranteed To Fit

Providing you the highest quality, direct fit replacement auto parts enforced to the strictest product standards.


USA Customer Support

Exceeding customers' expectations every day, our team of passionate auto enthusiasts are here to help.


Instructional Video Library

Thousands of how-to auto repair videos specific to year, make and model guide you step-by-step through your repair.

Loading...