How to Replace NT Speed Sensor 2006-11 Toyota Camry
Created on: 2017-10-10
How to remove, install, change or replace a rusted or defective speed sensor on 09 Toyota Camry.
-
step 1 :Removing the Air Intake
- Remove the 10mm bolts from the air box housing
- Disconnect the sensors
- Loosen the hose clamp on the air intake tube
- Lift the airbox
- Remove the air filter
-
step 2 :Removing the NT Speed Sensor
- Unplug the electrical connector
- Disconnect the sensor
- Remove the 12mm bolt from the sensor
-
step 3 :Installing the NC Speed Sensor
- Insert the sensor into the transmission
- Tighten the 12mm bolt to the sensor
- Connect the connector
-
step 4 :Installing the Air Intake
- Insert the air filter
- Place the cover on
- Connect the air intake tube and hose clamp
- Connect the connectors
- Tighten the 10mm bolts to the air box housing
Tools needed
-
12mm Socket
Socket Extensions
Paper Towels
10mm Socket
Ratchet
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
I'm going to remove the air box, just slightly out of the way, so that I can get to this connector better and undo it. Use a 10mm socket and ratchet. Loosen this up. There's a second one on the back side. Unplug this electrical connector here. Unplug this one here. This harness is actually connected to the air box, so can't pop it off, I'm just going to leave it here and move it to the side. Then loosen this clamp on the intake tube. Lift up the air box. Make sure those are fully released. Take our air filter out of here so it doesn't get damaged.
So, this harness here has a little push connector. I'm going to take these needle nose pliers and just push them together, and just pop it out. Put that aside. Put this aside, so it doesn't get damaged.
So, this harness here has a little push connector. I'm going to take these needle nose pliers and just push them together. And just pop it out. Put that aside. Put this aside, so it doesn't get damaged. The NT Speed Sensor is located on this part of the transmission, just under the battery tray. Push in the connector to unlock it, and pull the connector off. Use a 12 millimeter socket and extension racket, just fits in here under the battery tray. Break it free. Put this bolt aside, so I don't lose it. And just work on, just kind of wiggle this back and forth. Pull the sensor right out.
Here's the original sensor from our vehicle. Going to wipe off some of the oil on here, transmission fluid. See, it's similar in design, the brand new one from 1aauto.com, same style connector, same style single mounting hole, comes in the new O ring. This should fit in and work great.
Install the new sensor, reverse of the way the old one came out, slide it right into the opening. Push it down. O ring has some tension to it. I'll push it in. Line up the bolt hole. Reinstall the bolt. I'm just going to get it threaded in with my fingers. Then we'll just tighten it down with a socket and ratchet. Wait til it gets tight. That's when I will stop. Reconnect electrical connector. It clicks on. It's locked into place, and the sensor is installed.
Reinstall the lower air box. We've cleaned out all the debris that was in there. That's going to sit right back on the bracket. Get the bolts, and get them started. Tighten them down, socket and ratchet. Install the intake tube back into the box, just slides right over. Line it up on the radiator support. Just going to tighten those down, feel like I'm tight then I'll stop. Don't need to kill these, they're just holding plastic into the thin sheet metal.
Reinstall the air filter. Install the air box cover. It's got two tabs over here that need to go into these two hooks. Slide it over, and line up the little slot in the rubber with the plastic alignment tab. Make sure that the clamp is in the grooves. Tighten the screws holding in the air box. Then reconnect our electrical harness, clip it back into the spot on the air box were. Connect the mass air meter. And this little valve here, reconnect it.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Shop Products
How to Replace Speed Sensor 2001-05 Honda Civic
How to remove, install, change or replace a rusted or defective ABS wheel speed sensor on 01, 02, 03, 04, 05 Honda Civic
