Menu

1A Auto Video Library
Our how-to videos have helped repair over 100 million vehicles.

How to Replace Power Window Switch 01-04 Chrysler Sebring

Share on:

How to Replace Power Window Switch 01-04 Chrysler Sebring

Created on: 2014-03-05

How to repair, install, fix, change or replace a damaged, worn out, faulty or shorted power window switch on 01, 02, 03, 04 Chrysler Sebring.

  1. step 1 :Removing the Door Panel
    • Pry off the trim piece inside the door handle with a flat blade screwdriver
    • Pry off the trim piece inside the door pull with a flat blade screwdriver
    • Remove the Phillips head screw inside the door handle
    • Remove the Phillips head screw inside the door pull
    • Remove the four Phillips screws around the edge of the door panel
    • Pry off the mirror base trim piece with a flat blade screwdriver
    • Pry out the door panel by hand
    • Lift the door panel up and off
    • Unclip the door latch rod from the door handle
    • Disconnect the door lock wiring harness
    • Disconnect the window switch wiring harness
  2. step 2 :Removing the Window Switch
    • Remove the three T20 Torx screws from the back of the window switch
    • Pull off the window switch
  3. step 3 :Installing the Window Switch
    • Push the window switch into place
    • Insert the three T20 Torx screws into the window switch
  4. step 4 :Installing the Door Panel
    • Clip the latch rod into the door handle
    • Connect the door lock wiring harness
    • Connect the window switch wiring harnesses
    • Lift the door panel into place
    • Push in the door panel clips
    • Insert the Phillips screw into the door pull
    • Insert the Phillips screw into the door handle
    • Insert the four Phillips screws around the edge of the door panel
    • Push on the trim piece inside the door handle
    • Push on the trim piece inside the door pull
    • Push on the mirror base trim piece

Tools needed for replacement

  • Screwdrivers & Related

    Flat Blade Screwdriver

    Phillips Head Screwdriver

  • Star Drivers & Sockets

    T20 Driver

Installation Video
Watch video

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we show you how to replace the power window switch panel on this 2004 Chrysler Sebring 4-door sedan. It's the same process on these 4-door sedans from 2001 to 2004. We'll be using a new panel, the switch panel from 1AAuto.com, flat blade screwdriver, Phillips screwdriver, and a T20 Torx driver.

There are two trap doors here. There's one right here behind the door handle and another one here in the pull cup. All you want to do is take a flat blade screwdriver and stick it into the slot on the side of them and just pry them out. Now what you want to do is remove each of these Phillips screws. There are six in total. Just speed up the tape here as we remove those screws. Take your flat blade screwdriver and pry off that triangle panel. To release the clips on the back of the door panel you just want to pull out all the way around the door panel. Once you've done that you can lift it up and off of your door lock knob. In behind the back of the door panel you'll see here's your door handle rod. You just want to pop that clip up and pull that up and out. You want to disconnect the two harnesses here by just pushing in the tab and pulling them out. Now your door panel is free.

You'll see there are three T20 Torx screws that actually secure it to the door panel. Once the screws are removed it just pulls right out. Now to install your new switch panel from 1A Auto you just push it into place and replace those three T20 Torx screws. We're just going to fast forward as Don replaces these.

To reinstall the door panel you just want to take that door handle rod, put it back into place, and reclip it. Then you want to just reconnect your two harnesses. Once you've done that you want to just line up your door, put it up and over the door lock knob, and down into place. Then you just want to push those clips in around the edges of the door panel. Again, speed things up as we put those six screws back in. Now just replace your trap doors and that triangular panel.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Tools needed for replacement:

    Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Star Drivers & Sockets

  • T20 Driver

2001 - 2006  Dodge  Stratus
1998 - 2004  Dodge  Intrepid
2001 - 2004  Chrysler  Sebring
1999 - 2001  Chrysler  LHS
1998 - 2004  Chrysler  Concorde
1999 - 2004  Chrysler  300M

How to Permanently Attach Exhaust Flex Pipe No Clamps

How to Permanently Attach Exhaust Flex Pipe No Clamps

Watch this video to learn how to install a universal flex pipe, without using clamps. 1A Auto will show you how with a 2007 Audi A4.

Search Videos
Go To Top

Same Day Shipping

Need your part faster? Choose expedited shipping at checkout.

Guaranteed To Fit

Highest quality, direct fit replacement auto parts enforced to the strictest product standards.

USA Customer Support

Exceeding customers' expectations, our team of passionate auto enthusiasts are here to help.

Instructional Video Library

Thousands of how-to auto repair videos to guide you step-by-step through your repair.

Loading...