Menu

1A Auto Video Library
Our how-to videos have helped repair over 100 million vehicles.

How to Replace Washer Fluid Level Sensor 10-14 Volkswagen GTI

Share on:

How to Replace Washer Fluid Level Sensor 10-14 Volkswagen GTI

Created on: 2021-01-16

How to repair, install, fix, change or replace a broken, worn out, or damaged throttle position sensor on 10, 11, 12, 13, 14 Volkswagen GTI

  1. step 1 :Removing the Grille
    • Remove the T25 Torx bolts from the grille
    • Pull the grille forward and off the bumper
  2. step 2 :Removing the Bumper Cover
    • Remove the access panel in the wheel well
    • Remove the T25 bolt on either end of the bumper in the wheel well
    • Disconnect the fog light connector
    • Pull the fog light out
    • Remove the T25 Torx bolts from the splash shield
    • Pull the bumper cover out on both sides
    • Remove the bumper cover
  3. step 3 :Removing the Windshield Washer Fluid Level Sensor
    • Have a drain pan ready
    • Disconnect the wiring harness and connectors from the pump
    • Pry the sensor out with a flat blade screwdriver
  4. step 4 :Installing Windshield Washer Fluid Level Sensor
    • Insert the sensor into place
    • Connect the wiring harness and connectors to the pump
  5. step 5 :Installing the Bumper Cover
    • Insert the bumper cover into place
    • Tighten the T25 Torx bolts to the splash shield
    • Connect the fog light and connector
    • Tighten the T25 bolts on either end of the bumper
    • Connect the access panel in the wheel well
  6. step 6 :Installing the Grille
    • Insert the grille into place
    • Tighten the T25 Torx bolt to the grille

Tools needed for replacement

  • General Tools

    Drain Pan

  • Ratchets & Related

    Socket Extensions

    Ratchet

  • Screwdrivers & Related

    Flat Blade Screwdriver

  • Star Drivers & Sockets

    T25 Socket

Installation Video
Watch video

In this video, we will be removing and reinstalling a washer fluid pump in a 2010 Volkswagen GTI. We're going to take these T25s out of the front grille. We're using a T25 socket extension and a ratchet. Then, going to grab underneath the grille and just pull forward. There's little clips underneath. That came out easy. You may have to work at it a little bit. I'm going to pull this panel off. Grab underneath and pull. We have a T25 that goes straight up and down. I'm going to use our T25 socket and extension. Get on it. There's two more down here. We're going to pull our connector for our fog lights. You're going to push on this little tab here and then pull down. The connector will pull right out. Push down and pull that straight out.

The driver's side is the same. On the driver's side, the wiring harness had a retainer that's attached to the bumper. You're going to pull it straight out. We're going to take out all these T25s. There's one here, one here, one there, one there, one there, one there, these two, and these two. Now, on both sides, I'm going to grab right here and pull out. I'm going to take these last two out and we'll pull straight forward.

To disconnect this coolant level sensor, there is two tabs, one on top, one on the bottom. Going to push them real hard and pull straight out. All right to pull this out, I'm going to use a flat blade tool. Get in behind it, use your fingers and walk it out back and forth, pop it right out. There's the level sensor. All right, you want to make sure your rubber grommet is on the washer tank side. Then it'll be easier to install and then you want to push the sensor in, working it back and forth. Then we're going to connect the connector. Just push ‘til it clicks.

For ease of installation, it's easier if you have a partner when taking it off and can line it up. Install these two T25s. I'm going to install these T25s. Next, we're going to connect the marker light and push that in. Now, we're going to connect the fog light. Just push it on till it's locked in. Do the same for the driver's side. Right. We're going to install this last. We're going to install this T25 going up. You're going to push on the bumper and make sure it lines up while you're tightening it and put these torque screws in. Install the cover. Put it in the top and push in.

Install the grille and line it up down below. And push to lock it into place. Install these four T25 torx screws.

Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.

Tools needed for replacement:

    General Tools

  • Drain Pan

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Star Drivers & Sockets

  • T25 Socket


How to Use Touch Up Paint on any Vehicle

How to Use Touch Up Paint on any Vehicle

Check out this video from 1A Auto to learn how to use touch up paint to fix chips and scratches on your vehicle.

Search Videos
Go To Top

Same Day Shipping

Need your part faster? Choose expedited shipping at checkout.

Guaranteed To Fit

Highest quality, direct fit replacement auto parts enforced to the strictest product standards.

USA Customer Support

Exceeding customers' expectations, our team of passionate auto enthusiasts are here to help.

Instructional Video Library

Thousands of how-to auto repair videos to guide you step-by-step through your repair.

Loading...