1A Auto Video Library
Our how-to videos have helped repair over 100 million vehicles

How to Replace Sway Bar Link 02-09 GMC Envoy XL

Share on:
  1. step : Removing the Wheel (0:46)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Sway Bar Link (1:09)
    • Apply penetrating oil to the sway bar link nuts
    • Clean the sway bar link studs with a flat blade screwdriver, if necessary
    • Put a 4.5mm Allen wrench into the lower sway bar link stud
    • Remove the lower 18mm nut from the sway bar link
    • Put a 4.5mm Allen wrench into the upper sway bar link stud
    • Remove the upper 18mm nut from the sway bar link
    • Pull off the sway bar link
    • If necessary, cut the way bar link stud with a reciprocating saw, holding the sway bar in place with a pry bar and jack
  3. step : Installing the New Sway Bar Link (3:03)
    • Put the grease fittings onto the new sway bar link
    • Tighten the grease fittings with a 7mm socket and ratchet
    • Push the sway bar studs into place
    • Thread the two 18mm nuts onto the sway bar link by hand
    • Tighten the two 18mm nuts, holding the studs with a 17mm wrench
  4. step : Reattaching the Wheel (4:17)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Brought to you by, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of Thanks.

In this video, we're going to show you how to replace a sway bar link of this 2003 GMC Envoy XL. We show you on the passenger side, but the driver's side is a similar procedure. The items you'll need are a new sway bar link from, 7mm and 19mm socket and ratchet, 17mm and 18mm wrenches, 4.5mm Allen wrench, flat blade screwdriver, torque wrench, jack and jack stands, and depending on the condition of your vehicle, you may also need a pry bar and a reciprocating saw.

Start out by removing the wheel and tire. Pry off the hubcap. If you don't have the benefit of air tools, keep the wheel on the ground. Loosen the lug nuts first, then raise and secure the vehicle. For this repair you have to lift up both front tires evenly. Use jack stands to secure it. Then remove the lug nuts, wheel, and tire.

Start off by just lightly spraying the nut with some penetrating oil on both sides of your sway bar link. You want to make sure it doesn't get into the hole on the front of that stud because you want to make sure that the Allen wrench can stay in there. Place an 18mm wrench onto the nut and then, using a 4.5mm Allen wrench, just stick it into that stud. Then, just remove that nut. Now, you may need to clean out the inside of that stud so you can get the Allen wrench in there, on the back here. Ours was filled with dirt. We just scrape it out with a flat blade screwdriver. Then repeat the process that you had done on the lower stud.

On our vehicle we had an issue. We basically got the nut off on the top side. We got it mostly off, but then the nylon locking just locked it up and we couldn't get it out anymore. We're using a reciprocating saw to cut the stud on the sway bar link. We're using that pry bar. We're just supporting it so that the sway bar doesn't move up and down as we're using the saw. Hopefully you don't have to get to this point, but if you do this is how you can overcome not being able to get the nut off or if it's broken or frozen or anything like that.

On the right, is the old link. On the left, is the new one. You can see they are similar and they're going to fit exactly the same. Take your new sway bar link and just put the grease fittings into place. Using a 7mm socket and ratchet just tighten up those grease fittings. Push the studs on the sway bar link back into place. Then twist the nuts into place. Then just tighten up that 18mm nut and hold the inside nut with a 17mm wrench. Repeat the process with the other stud.

Replace your wheel. Replace the lug nuts and tighten them up preliminarily. Lower the vehicle, tighten them the rest of the way and torque each of them to a hundred foot pounds in a crossing pattern.

We hope this video helps you out. Brought to you by, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack
  • Reciprocating Saw

  • Hex Wrenches

  • 4.5mm Hex Wrench

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 19mm Socket
  • 7mm Socket

  • Wrenches - Metric

  • 18mm Wrench
  • 17mm Wrench

2003 - 2003  Oldsmobile  Bravada
2003 - 2003  Isuzu  Ascender
2003 - 2003  GMC  Envoy
2002 - 2002  Oldsmobile  Bravada
2002 - 2002  GMC  Envoy
2002 - 2002  Chevrolet  Trailblazer
2003 - 2003  Chevrolet  Trailblazer EXT
2003 - 2003  Chevrolet  Trailblazer
2002 - 2002  GMC  Envoy XL
2002 - 2002  Chevrolet  Trailblazer EXT
2003 - 2003  GMC  Envoy XL
2002 - 2003  GMC  Envoy
2002 - 2003  Oldsmobile  Bravada
2002 - 2003  Chevrolet  Trailblazer
2002 - 2003  GMC  Envoy XL
2002 - 2003  Chevrolet  Trailblazer EXT
Search Videos
Go To Top

Same Day Shipping

Orders ship same day when ordered by 2pm ET. Need your part faster? Choose expedited shipping at checkout.

Guaranteed To Fit

Providing you the highest quality, direct fit replacement auto parts enforced to the strictest product standards.

USA Customer Support

Exceeding customers' expectations every day, our team of passionate auto enthusiasts are here to help.

Instructional Video Library

Thousands of how-to auto repair videos specific to year, make and model guide you step-by-step through your repair.