1A Auto Video Library
Our how-to videos have helped repair over 100 million vehicles

How To Replace Side Marker Light and Bulb 04-11 Mazda 3

Share on:
  1. step : Removing the Side Marker Light (0:33)
    • Remove the three clips on the back side of the front wheel well.
    • Remove the one screw near these clips.
    • Reach behind the inner fender and release the clip.
    • Reach up into the inner fender and push the tabs on the backside of the side marker light to release it.
    • Pull the light forward and disconnect the wiring harness.
  2. step : Reinstalling the Side Marker Light (1:17)
    • Plug in the wiring harness.
    • Push the front end of the light in first then the back to snap it into place.
    • Put the inner fender back into place.
    • Insert the clips.
    • Insert the screw.

Brought to you by, your source for quality replacement parts and the best service on the internet.

Hi, I'm Don from 1AAuto. I hope this helpful video helps you out. The next time you need a part for your vehicle, think of Thanks.

In this video, we're going to show you how to service a little safety side marker light for the front fender. These are sealed units so if one of them is out, you need to replace it with a whole entire unit. It's pretty easy. You'll need a Philips screwdriver, a flat blade screwdriver. There are three clips. You can see two black clips lower down. There's three clips and one screw you'll have to remove in order to access the back of the rear of your front fender. Pull the inner fender out, reach behind, release that clip and then pull your inner fender the rest of the way out.

Now, looking up inside, you can see the back of the light and the tab you have to squeeze. Squeeze the tab and pop the light out and you can see here, there's the tab you squeeze, pop it out and then on the connector, there's a little tab, squeeze and disconnect. Install the new one, just reverse. Plug it back in, put the slot in first and snap it in and then put the inner fender back in place with the clip on and re-secure the clips. You pull the center out of the little clips, pull the center out a little bit, push the clip in and then push the center in the lock and then put the screw back into that middle clip.
We hope this helps you out.

Brought to you by, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the internet and in person.

Tools needed for replacement:

    Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

2011 - 2013  Mazda  2
2006 - 2010  Mazda  5
2000 - 2006  Mazda  MPV
2004 - 2011  Mazda  3

11-12 Mazda 2; 04-11 Mazda 3; 04-06 MPV; 06-10 Mazda 5 Side Repeater Light LH = RH

Mazda 2 3 5 MPV Driver or Passenger Side Repeater Light TYC

This part replaces:

  • Partslink MA2570102
  • Hollander 116-59903
  • TYC 18-0657-00-1
  • DEPO 316-1413N-AF
  • OE # GJ6A51120E
  • TYC 18-0657-00

Part Details

Search Videos
Go To Top

Same Day Shipping

Orders ship same day when ordered by 2pm ET. Need your part faster? Choose expedited shipping at checkout.

Guaranteed To Fit

Providing you the highest quality, direct fit replacement auto parts enforced to the strictest product standards.

USA Customer Support

Exceeding customers' expectations every day, our team of passionate auto enthusiasts are here to help.

Instructional Video Library

Thousands of how-to auto repair videos specific to year, make and model guide you step-by-step through your repair.