Menu

1A Auto Video Library
Our how-to videos have helped repair over 100 million vehicles

How to Replace Serpentine Belt 07-13 Mini Cooper S

Share on:
  1. step : Removing the Wheel (0:30)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the 17mm lug bolts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug bolts
    • Pull off the wheel
  2. step : Removing the Wheel Well Liner (1:20)
    • Remove the 10 mm nuts securing the front and rear edges of the liner
    • Remove the push clip retainers by loosening the Phillips head center and prying it out
    • Remove the two T30 screws near the top of the liner
    • Pull the lining out from under the fender trim and pull it out
  3. step : Removing the Serpentine Belt (3:29)
    • Remove the 10 mm bolt to remove the AC line bracket
    • Pull the handle to release the water pump drive friction gear
    • The release strip hooks onto a tab of the housing
    • Use a 13/16 box end wrench, or a 21 mm 12-point wrench to rotate the belt tensioner
    • Have an assistant lock the service mode pin, you are then free to release the tensioner and continue work
    • Remove the serpentine belt
  4. step : Installing the Serpentine Belt (6:24)
    • The serpentine belt loops around the three pulleys
    • Rotate the serpentine belt tensioner to release the service pin, then release the tensioner
    • Pull the water pump tensioner strip to release it from the tab and return it to position
    • Reinstall the AC line bracket and secure it with the 10 mm bolt
  5. step : Installing the Wheel Well Liner (8:50)
    • Insert the wheel well liner into the wheel well
    • Install the two T30 screws near the top
    • Install the two 10 mm nuts at the front and rear edges
    • Install the push pin retainers
  6. step : Installing the Wheel (10:48)
    • Slide the wheel into place
    • Start the 17mm lug bolts by hand
    • Tighten the lug bolts by hand
    • Lower the vehicle to the ground with minimal weight on the wheel
    • Tighten the lug nuts to 88 foot-pounds in a crossing or star pattern
    • Lower the vehicle completely

Hi, I'm Mike from one 1A Auto. We've been selling auto parts for over 30 years.

What's up, guys? I'm Andy from 1A Auto. Here, I'm going to be showing you how to replace the serpentine belt in this 2007 Mini Cooper S. If you need parts for your vehicle, click the link in the description and head over to 1AAuto.com. Going to take the center cap off. I'll just use a straight blade screwdriver. Slide it in here. Pop the cap off.

Now, I'm going to take a 17-millimeter socket and breaker bar. I'm going to loosen up these lug nuts. Okay. Now, I'm going to raise the vehicle. I'm using a two-post lift. If you're doing this at your house, you can use a jack and jack stands.

All right. Now I'm going to take these lug bolts out. Just use the 17-millimeter socket to help me out. When I get to the last lug bolt, I'm going to hold the wheel on there. Push down so that the wheel doesn't fall. Then I can grab the wheel, pull it off.

Now I want to take this inner wheel liner out from underneath here. I'm going to use a 10-millimeter socket and ratchet. Just take this fastener out on the back. Then on the front here, if there's anything securing the front. This vehicle, I believe there's another shield here, but it's missing on this vehicle. So check that.

I'm going to take all these push clips out. I'm just going to use a Phillips-head screwdriver. Loosen up the center part of the push clip. Then you can slide the clip out just like that. So there's seven of these clips that you have to pull out. There's one here, one here. There's two right here. There's one right here. One on the backside here, and then also one right there.

I have these two Torx bolts that I want to take out. I'm going to use a T30, an extension, and a ratchet. Take these two bolts out. Now I'm going to grab the inner fender well. Pull it out.

Oh, there's one more. There's one more retainer right here. Take the Phillips-head screwdriver. Loosen this up. Then just slide it out. I'm going to remove this AC bracket right here. This just holds this AC line in. I'm just going to use a 10millimeter socket, an extension, and a ratchet to take this bolt out. Take that bolt out. You can slide this bracket out of the way a little bit, just like that. This bracket can come off like that. It'll just reclip in afterwards.

Next, we're going to release the tension on the friction gear. This is a little gear that puts pressure on the water pump drive. Release this right here. Pull this out. Then pull that, and then there's a little tab right there that gets locked on there and then that's loose. So I'm going to need to release the tension from the tensioner, the belt tensioner. I'm going to be underneath with a wrench to loosen that up, and then I'm going to need a partner to come up here and push on this little pin. And then I can release the tensioner, and that'll hold it in service mode.

So there's an actual tool for this tensioner, but we don't actually have it. So we're going to use a 13/16ths box wrench that's straight, or you could use a 21-millimeter 12 point. So I'm just going to slide it up from underneath here. Get onto the tensioner, the back side, and I'm going to take the tension off the belt. And then my partner's going to push the pin.

All right. Carefully, with that bracket out of the way, I'm going to push on this wrench.

There it is.

Did you get it?

Yep.

All right. Then I can loosen up on the wrench. Be very careful when you're doing this. You don't want your fingers to get caught anywhere. And I can pull the wrench out, and the pin is in. Now we're going to slide the belt off the alternator. Just lift up. That will slide off there. You can slide it out over here. You can lift up off that tensioner for the water pump and then slide the belt over here off the AC compressor. And then slide it in front of this AC hose, and pull it right out.

Now if you have a new belt, you can install it. Just slide it over this AC line. Go down here. Then we go over the AC compressor first and then go over the crank. Lift up on this tensioner. It goes near the water pump, and then slide it up over the alternator. Make sure the belt's in all the grooves, and there you go.

Now I'm going to take my 13/16ths wrench and slide it over the tensioner. All right, and that's in position. And just make sure all the pulleys, everything's, all the grooves are in the pulleys and I can pull back on the tensioner. I'm going to push the tensioner this way first. That's going to release the pin, and then I can release the tensioner.

Be careful. Make sure your fingers don't get in the way of any of the pulleys or anything, and we can pull the wrench off. All right, now we're going to release the tension on this tensioner. Just grab this little strap, pull it off that lock there, and release it. Push that back in. Just like that.

Now I'm just going to reinstall this bracket. Just get this into position. I'll take the 10-millimeter bolt, get that started. Now I'm going to just snug it up with my ratchet. I want to hold the bracket into the right position when I snug down the bolt. And it's good. And right here, I can squeeze this bracket together so it locks in place. Just like that.

And now we're going to install this inner fender well. Just get this around the strut on the back side here. Just got to work it back into position. Get this lined up right there. Just going to take these bolts and get these started. Whoops. A torque screw. Get that one started, and then another one goes right here. Get that one started.

I'm going to take this little nut, get that one started underneath there. Then I'm going to push all the push pins in. Make sure you get them all lined up. It's easier to angle these push pins a little bit and try to twist them, get the fingers in, and then lock them down.

Now I'm going to tighten this nut up. I'll just use a 10-millimeter socket, extension, and a ratchet and just snug it up. There we go. We're going to tighten down these bolts, the T-30s, and just snug these up, that one and this one.

Now we're going to install the wheel. Line this up with the holes. Take the lug stud. Get this started. Now I'm going to take my 17-millimeter socket and a torque wrench. I'm going to torque these lug studs to 88 foot-pounds. I'm doing this in a cross pattern so that it torques the wheel down evenly. I'm just going to go around again, double-check. I'm going to reinstall the cap. Line this up with this location right here and press it on.

Thanks for watching. Visit us at 1Aauto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Sockets - Metric

  • 17mm Socket

  • Star Drivers & Sockets

  • T30 Socket

  • Wrenches - Metric

  • 21mm wrench

  • Wrenches - SAE

  • 13/16 Inch Wrench


Search Videos
Go To Top


Same Day Shipping

Orders ship same day when ordered by 2pm ET. Need your part faster? Choose expedited shipping at checkout.


Guaranteed To Fit

Providing you the highest quality, direct fit replacement auto parts enforced to the strictest product standards.


USA Customer Support

Exceeding customers' expectations every day, our team of passionate auto enthusiasts are here to help.


Instructional Video Library

Thousands of how-to auto repair videos specific to year, make and model guide you step-by-step through your repair.

Loading...