How to Replace Running Light Bulb Socket 2001-06 Chevy Silverado
Created on: 2014-05-07
Learn how to replace the running light bulb socket on your 00-06 Chevy Silverado or GMC Sierra with this video from 1A Auto.
-
step 1 :Removing the Headlight
- Remove the two locking pins from the headlight
- Pull the light forward and out
- Twist the bulb sockets out of the light
-
step 2 :Removing the Parking Light
- Unhook the parking light tab
- Pull the light forward and out
- Twist the bulb sockets out of the light
-
step 3 :Removing the Driving Light Socket
- Cut the shielding from the parking light socket wiring with a razor
- Cut the wires with wire cutters
- Pull the bulb out of the socket
-
step 4 :Installing the New Driving Light Socket
- Strip 1/4 inch of coating off the end of the wires for the new driving light socket
- Twist the wire filaments
- Insert the wires into a splice
- Crimp the splice with wiring pliers
- Strip 1/4 inch of coating off the end of the driving light wires on the vehicle
- Twist the wire filaments
- Push the wires into the splices
- Crimp the splice with wiring pliers
- Put the shielding over the wires
- Push the bulb into the new socket
-
step 5 :Reinstalling the Parking Light
- Twist the bulb sockets into the parking light
- Push the parking light into place
-
step 6 :Reinstalling the Headlight
- Twist the bulb sockets into the headlight
- Push the headlight into place
Tools needed
-
Razor Blade / Gasket Scraper
Wire End Cutters
Wire Cutters
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the light socket on one of the driving lights on this 2002 Suburban. Often the light sockets burn up and melt because the driving lights are on constantly. This is the same for any Suburban of this age as well as the GM trucks and other SUVs. Tools you need are new light sockets from 1AAuto.com, wire cutters, wiring pliers and a razor blade or a knife to cut some electrical tape.
Start out by removing the headlight which is the two locking pins at the top and then pull the light out and disconnect the connectors and then remove the parking light by reaching down in and clipping the tab and pulling the light out and remove the driving light socket.
Take your parking light socket and cut this shielding and pull it back. Using wire cutters, just clip these wires. Just take your bulb out and you'll put it in your new one. Interesting to note that the socket was already replaced on this vehicle, so you can see on the left is the one that was in there. On the right is the new one from 1A Auto.
I'm going to crimp or splice the wires together, so take off about 1/4 inch to 1/2 an inch of the end, twist the filaments on the wire, insert it into the splice and then use your wiring pliers to crimp the end line splice and repeat it for the other side or the other wire. Now we just need to repeat the process on these wires, just strip them. Again push the other side of the wire. It doesn't matter which wire goes to which wire on the new socket as it just completes the circuit. We'll put the wire in and crimp them with the wiring pliers. Once you've done that, your socket's now reconnected and you can just put this shielding back over the wires. Push your bulb into your new socket, and then, you can twist your sockets back into your parking light, put your parking light back into place and then put your headlight back in to place. Once everything's back in place, you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Shop Products
Bulb Socket 2 Piece Set Dorman TECHoice 1ALPP01047
- 2 Piece Set
- (2) Bulb Sockets
How to Replace Turn Signal 1998-2000 Toyota Sienna
Watch this video to learn how to replace the turn signal lights on your 98-03 Toyota Sienna.
