How to Replace Rear Window Regulator 2002-06 Jeep Liberty
Created on: 2014-01-24
If you need a new window regulator for your 02-06 Jeep Liberty, check out this video and 1A Auto will show you how to do it yourself!
-
step 1 :Removing the Door Panel
- Pry off the trim piece inside the door handle with a flat blade screwdriver
- Remove the Phillips head screw inside the door handle
- Remove the Phillips head screw inside the door pull
- Pry out the door panel clips with a putty knife or flat blade screwdriver
- Lift the door panel up and off
- Disconnect the door handle rod from the door handle
- Remove the three Phillips head screws from the speaker
- Disconnect the speaker wiring lead
- Pull off the speaker
- Carefully peel off the water shield
-
step 2 :Removing the Window Regulator
- Loosen the clips that hold the window to the regulator with a flat blade screwdriver
- Raise the window by hand
- Hold the window in place with painter's tape
- Push out the black clip holding the regulator cable to the door
- Remove the three 10mm bolts from the regulator
- Remove the three 10mm bolts from the window motor
- Push the red clip on the window motor
- Disconnect the window motor lead
- Pull the window regulator out through the door
-
step 3 :Reinstalling the Regulator
- Swap over the old bolts to the new regulator
- Insert one of the bolts into the window regulator
- Push the regulator into the door
- Hang the regulator by its bolt
- Insert the three10mm bolts into the regulator
- Insert the three 10mm bolts into the window motor
- Remove the painter's tape from the window
- Lower the window onto the regulator
- Insert the clips that hold the window to the regulator
-
step 4 :Reinstalling the Door Panel
- Put the water shield into place
- Connect the speaker wiring lead
- Put the speaker into place
- Insert the three 10mm bolts into the speaker
- Connect the latch cables to the door handle
- Lift the door panel into place
- Push in the door panel clips
- Insert the Phillips screw into the door pull
- Insert the Phillips screw into the door handle
- Push on the trim piece inside the door handle
Tools needed
-
Flat Blade Screwdriver
Phillips Head Screwdriver
Putty Knife
10mm Socket
Ratchet
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a rear window regulator on this 2006 Jeep Liberty. We show you on the passenger side, but the driver side is the same procedure. The items you'll need for this include a new rear window regulator from 1AAuto.com, a Phillips screwdriver, a flat blade screwdriver, a 10mm socket and ratchet, and a putty knife. If you drive a 2006 Jeep Liberty, it's important that before purchasing a new window regulator you first locate your manufacturing date on your vehicle. The manufacturing date can be found on the inside of the driver's door (as you can see on this picture) and you'll notice on 1AAuto.com that we have two types of regulators for two different manufacturing dates. If yours was made after February of 2006, you're going to need the other regulator.
Start off by prying out this little panel behind your door handle. There's a Phillips screw in there and one in the pull cup. Just go ahead and remove those. Using a patty knife or flat blade screwdriver, pry out the door panel so you can get your hand behind it. Then near the clips, pull directly out and this will release those clips. Again, find the clip, pull out, and when you get to this point, reach in behind the door panel and push those last two clips along the top out. The door panel lifts up and off.
At the back of your door handle, push this clip off your door handle rod and push it down and out. Remove the three Phillips screws holding your speaker in place. Once those are removed, pull your speaker out, push the tab on the harness to disconnect it, and carefully peel off your water shield making sure you don't damage it.
Your window is held to your regulator by this metal clip right here. Using a flat blade screwdriver, just pry that clip out, and then you can push your window out of the regulator and slide it all the way and tape it all the way up. Push this black clip through the door by pushing the tabs, and then you want to loosen these three bolts: each of them 10mm. Now loosen these three 10mm bolts. Slide the motor up and through the door, and do the same thing with the three bolts for the regulator. Then you want to angle it so you have better access to the wire harness on the motor. To disconnect the harness, pry the red clip out and push the tab on the harness and pull it free. Angle the regulator and pull it up and out through that big bolt top of the door.
In the front is the old regulator; behind is the new one from 1A Auto. You can see they look a little bit different, but they will work identically. The new one from 1A Auto is just an upgraded style of the older one and we'll mount exactly the same. You do have to loosen up these three bolts so you can hang the regulator back on to the door, and then take the three bolts from your old motor and put them into your new one. We'll just fast-forward as Don does this.
Now, feed your new regulator down into the door and hang the regulator back on to the door as well as the motor. Tighten up those six 10mm bolts, reconnect your motor harness, and then push that red clip in to lock it. Remove the tape from your window and slide the window down into the regulator and then push the window forward into that slide to clip it.
Replace your water shield, making sure that that interior door handle rod goes back through it and that your lock rod goes through it as well. Reconnect the harness on the back of your speaker. Push the speaker back into place, reinstall those three Phillips screws, and tighten them up.
To reinstall the door panel, push your door handle rod back up into the door handle and re-clip it. Then put your door panel down over the lock and on to the window sill. Check behind the door panel, and make sure the clips are lined up. Then hit them into place. Then replace those two Phillips screws and that panel behind the door handle.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Shop Products
Jeep Liberty Rear Driver & Passenger Side Power 2 Piece Power Window Motor & Regulator Assembly Set TRQ WRA50670
- Power
- 2 Piece
- (1) Rear Passenger Side Power Window Motor & Regulator Assembly
- (1) Rear Driver Side Power Window Motor & Regulator Assembly
1AWRG00023 Buick Regal Century Oldsmobile Intrigue Window Regulator
Everything that you want to know about part number 1AWRG00023. It's a power window regulator for a Buick Century, Regal, and Oldsmobile Intrigue, years 97, 98, 99, 00, 01, 02, 03, 04, or 05. It fits the driver's side front door, and it includes the power window motor. New Window Regulator from 1AAuto.com.
