How to Replace Rear Parcel Shelf Speakers 2005-10 Chrysler 300
Created on: 2017-02-09
Find out how to replace the rear parcel shelf speakers yourself with this how-to video
-
step 1 :Removing the C Pillar Trim
- Feel the bracket underneath the rear seat and pull up firmly
- Remove the lower seat cushion
- Pull the tabs and lower the rear seat
- Fold back the flap and remove the 10mm bolt from the side seat cushion
- Pull the side seat cushion up and out
- Repeat this process for the other side
- Remove the two Phillips head screws in the pillar trim
- Pop the top of the panel out and up
- Remove the trim
- Remove the T50 Torx from the seat belt
- Pry the seat pillar out
- Remove the trim
-
step 2 :Removing the Parcel Shelf
- Remove the 18mm nut holding the center seatbelt to the floor
- Fold down the seat
- Remove the clips from the parcel shelf with a trim tool
- Pop the seat belt panel out of the parcel shelf
- Pull the seat belt through the parcel shelf
- Pull the parcel shelf out of the vehicle
-
step 3 :Removing the Speakers
- Remove the four 7mm bolts from the speaker
- Lift the speaker up and out
- Disconnect the speaker electrical connector
-
step 4 :Installing the Speakers
- Connect the speaker electrical connector
- Lower the speaker into place
- Start the four 7mm bolts by hand
- Tighten the four 7mm bolts
-
step 5 :Installing the Parcel Shelf
- Thread the seat belt through the parcel shelf
- Pop the seat belt panel into the parcel shelf
- Put the parcel shelf into place
- Push the clips into the shelf
- Fold up the seat
- Put the seat belt onto its stud
- Fasten the 18mm nut onto the seat belt
- Tighten the 18mm nut to 25 foot-pounds of torque
-
step 6 :Installing the C Pillar Trim
- Insert the seat belt through the pillar
- Press the pillar trim into place
- Pull the interior weatherstrip over the c pillar
- Tighten the T50 Torx bolt to the seat belt
- Torque the bolt to 25 foot-pounds
- Install the bottom and then top of the lower c pillar
- Tighten the two Phillips head screws to the trim
- Tighten the 10mm screw to the trim
- Tighten the 10mm bolts to the cushion
- Press on the back seat, push down, lock it in
Tools needed
-
Socket Extensions
Torque Wrench
Phillips Head Screwdriver
18mm Socket
7mm Socket
10mm Socket
Ratchet
Trim Tool Set
Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years. We're dedicated to delivering quality auto parts, expert customer service, fast and free shipping, all backed by our 100% satisfaction guarantee. Visit us at 1AAuto.com, your trusted source for quality auto parts.
In this video we're going to be working with our 2006 Chrysler 300. We're going to show you how to remove and replace your vehicle's rear parcel shelf speakers. These are the ones up in the shelf behind your rear seat under the window, not the ones in your rear door. If you like this video, please click subscribe. We have a ton more information on this and many other vehicles. If you ever need parts for your car, you can follow the link down in the description over to 1AAuto.com. Here are the items you'll need for this repair.
Remove the rear seat cushion. To do this, you'll grab right where you feel the bracket underneath and pop up firmly, and there's another one on the opposite side. Lift out and remove the lower seat cushion. Pull the tabs to lower the rear seats. Fold down the little flaps, and you'll find a 10mm bolt for the side seat cushion on each side. Remove that with a 10mm socket and ratchet. Once the bolt is removed, firmly grab the top of the seat cushion and pull out to release the clip. We'll repeat this process with the opposite side.
Remove the two Phillips head screws in the lower seat panel. Now you may need to fold this seat up in order to get to the lower screw. Pop the top of the panel out and then up and repeat this process with the lower panel on the opposite side. Use a T50 Torx to remove the seat belt bolt. Once the bolt is out, lower the seat back down. Pop the C pillar off. The last one in the back corner is the trickiest. You're going to actually want to reach back there and pop that manually so you don't break it. Pull your seat belt through the panel. Repeat these steps on the opposite side.
Using an 18 mm socket and ratchet, remove the nut securing the center seatbelt and buckle to the floor. Remove the buckle and the seatbelt.
Using your 1A Auto interior trim removal tools pop the center clip out of the parcel shelf. Pull the parcel shelf towards you. If you need to remove it fully, you can pop this panel out, lay it down and pull your seatbelt and buckle through and remove the shelf from the vehicle.
Using your 1A Auto interior trim removal tools, pop the center clip out of the parcel shelf. Pull the parcel shelf towards you. If you need to remove it fully, you can pop this panel out, lay it down, and pull your seatbelt and buckle through, and remove the shelf from the vehicle.
Remove the four 7mm screws securing your speaker to the rear deck. Lift up and remove the speaker from the deck. Push down and release your electrical connector.
Reconnect the electrical connector and place the speaker back into the deck. Now that is cut pretty tight, so it's going to line itself up pretty well. Just to be safe, we'll start all four of our 7mm screws by hand before tightening any of them down.
Send your seatbelt and buckle back through the opening in your parcel shelf. Snap that back into place.
Move the shelf back into position and reinstall the plastic clip in the center. Fold the seat back up. Reinstall the base of your center seatbelt as well as the 18 mm nut which we'll tighten down with our 18 mm socket and ratchet before torquing to 25 foot-pounds.
Reinstall the seat belt through the C pillar. Line up the C pillar and snap all of the tabs back into place. Be sure to pull the interior weatherstrip over the C pillar before snapping it entirely into place. Reinstall the T50 Torx bolt at the bottom of your seat belt. Tighten it down and then torque to 25 foot-pounds. You'll have to fold the seat down and install the bottom of the C pillar cover first, then snap the top in. Lay the seat back up and install your two Phillips head screws.
Reinstall the seat panel. Remember to snap the top into place and reinstall your 10mm screw on- And repeat this process on the other side. Reinstall the back seat. Make sure that you pull all of your seat belt buckles up to the appropriate slots in the seat. Slide the rear down into place. Line up the front and then push down to lock it in.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Why Does My New Radiator Have Extra Ports
Got a new radiator but it has extra ports or connectors? That's normal in the aftermarket. Check this video out to see why its OK!
