How to Replace Rear Inside Door Handle 2001-06 Chrysler Sebring
Created on: 2013-11-08
How to repair, install, fix, change or replace a broken or snapped off interior door handle on Chrysler Sebring, years 01, 02, 03, 04, 05, and 06.
-
step 1 :Removing the Door Panel
- Pry off the trim piece inside the door pull with a flat blade screwdriver
- Pry off the trim piece inside the door handle with a flat blade screwdriver
- Remove the Phillips head screw inside the door pull
- Remove the Phillips head screw inside the door handle
- Remove the two Phillips screws at the bottom of the door panel
- Pry out the door panel with a putty knife
- Lift the door panel up and off
- Unclip the latch rod from the door handle
- Disconnect the window switch wiring harness
-
step 2 :Removing the Door Handle
- Remove the two T20 Torx screws from the back of the door handle
- Push out the door handle
-
step 3 :Installing the Door Handle
- Push the door handle into the door panel
- Insert the two T20 screws into the door handle
-
step 4 :Reinstalling the Door Panel
- Put the water shield into place
- Connect the window switch wiring harnesses
- Clip the latch rod to the door handle
- Lift the door panel into place
- Push in the door panel clips
- Insert the two Phillips screws at the bottom of the door panel
- Insert the Phillips screw into the door handle
- Push on the trim piece inside the door handle
- Insert the Phillips screw into the door pull
- Push on the trim piece inside the door pull
Tools needed
-
Flat Blade Screwdriver
T20 Driver
Phillips Head Screwdriver
Putty Knife
10mm Socket
Ratchet
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the rear interior door handle on this 2004 Chrysler Sebring. The tools that you're going to need for this are a Phillips screwdriver, a flat blade screwdriver, a 10mm socket and ratchet, and a T20 Torx bit.
To start off, use your flat blade screwdriver and just pry up these two little trap doors here. You'll see there's one Phillips screw in there. There's one in there. If you come down here, there's two more. We'll just fast-forward as Don removes those four Phillips screws. You want to just pry out the panel to release the clips and we'll do this on the other side. Then your door panel will just lift up and off.
On the back side of the door panel you'll see this little clip here on your door handle rod. You just want to pry this off with your flat blade screwdriver and then you want to just push the tab on this harness and disconnect it and your door panel is free.Now to remove your interior door handle, you just want to flip over your door panel and you'll see on the back side of your interior door handle are those 2 T20 Torx screws. You want to just go ahead and remove those and once those are removed you just push your door handle right out and there it is.How to install your new one, just push it into place and replace those 2 T20 Torx screws on the back.
Now to re-install your door panel, you just want to push that harness back into place. Then take your door handle rod and put the clip back onto it. Then you just want to line your door panel up over the block and put the clips in around the edges. We're going to fast forward as Don replaces those four Phillips screws and closes the two trap doors. You're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
How To Replace Interior Door Handle 1996-2000 Honda Civic Sedan
How to repair, install, fix, change or replace a broken or snapped off interior door handle on Honda Civic sedan, years 96, 97, 98, 99, or 00.
