1A Auto Video Library
Our how-to videos have helped repair over 100 million vehicles.

How to Replace Power Window Switch 97-01 Toyota Camry

Share on:

How to Replace Power Window Switch 97-01 Toyota Camry

Created on: 2021-01-16

New Power Window Switch from How to repair, install, fix, change or replace a damaged, worn out, faulty or shorted power window switchon 97, 98, 99, 00, 01 Toyota Camry

  1. step 1 :Removing the Power Window Switch
    • Pry up the window switch with a flat blade screwdriver
    • Disconnect the window switch wiring harness
    • Remove the three Phillips screws from the switch
    • Remove the switch from the panel
  2. step 2 :Installing the Power Window Switch
    • Insert the window switch into the trim
    • Tighten the three Phillips screws to the switch
    • Connect the window switch wiring harness
    • Press the window switch into the door panel

Tools needed for replacement

  • Screwdrivers & Related

    Flat Blade Screwdriver

    No. 2 Phillips Screwdriver

Installation Video
Watch video

Brought to you by, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of Thanks.

In this video, we are going to show you how to replace the main power window switch. This is a 1998 Toyota Camry and the items that you are going to need is a new side window switch from, a flat-blade screwdriver, and a Phillips screwdriver.

The steps to remove the master window switch and the passenger window switch are very similar. They are nearly the same, but the switch itself will look just a little bit different. Using a flat blade screwdriver, pry up on the back to release it from the door panel. Lift up.

Pull to the back to release this hook from underneath the panel. Press down on the tab to release the connector. This one is a little stuck. Use a small screwdriver to help release it. Remove the three Phillips-head screws with a number two Phillips screwdriver. Remove the switch from the panel.

Here we have our old master window switch from our vehicle and our new part from As you can see, the switches are the same size and shape. The graphics are a little bit different, but it's still going to work just the same. We had the two position automatic down feature on the driver's window switch. All the other switches work nice and smooth. These are all full of dirt and grime from being in the vehicle for almost 200,000 miles now. Some nice, smooth switches here. We're going to have good contact.

Make sure your windows go up and down every time you want them to. Also, the door lock feature is being located here, and the safety to disable the passenger and rear windows. We have the same connector on the bottom. We have the same two pins at the bottom, one pin at the top. You can see it fits into our trim nicely. It'll go right in, direct fit just like our original equipment.

If your window switch is broken, sticky, or not doing everything it should, this new part from 1AAuto is going to fix you up right. We have our new switch from 1AAuto.

We'll reinstall the trim for our vehicle with the three Phillips head screws. There is no need to put these in real tight. Just get them in there snug. You don't want to break the plastic.

Reinstall the connector into your switch. Slide the front hook under the door panel, and snap the rear into place. Check for proper operation of your switch.

Our door won't stay locked because the driver's door is open and the key is in the vehicle. Lock and unlock work fine. The window goes up. Now, sometimes you have to program the automatic down feature when you get to the bottom. Push the switch all the way in and count 10 seconds. Roll the window all the way up and then try the auto down feature.

Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit Also check out our other helpful how-to and diagnosis videos.

Tools needed for replacement:

    Screwdrivers & Related

  • Flat Blade Screwdriver
  • No. 2 Phillips Screwdriver

1997 - 2001  Toyota  Camry
1998 - 1999  Toyota  Avalon
1998 - 2002  Toyota  Corolla
2000 - 2005  Toyota  Echo
1998 - 1998  Toyota  4Runner
Search Videos
Go To Top

Same Day Shipping

Need your part faster? Choose expedited shipping at checkout.

Guaranteed To Fit

Highest quality, direct fit replacement auto parts enforced to the strictest product standards.

USA Customer Support

Exceeding customers' expectations, our team of passionate auto enthusiasts are here to help.

Instructional Video Library

Thousands of how-to auto repair videos to guide you step-by-step through your repair.