Menu

1A Auto Video Library
Our how-to videos have helped repair over 100 million vehicles

How to Replace Parking Brake Shoe Hardware 07-10 Dodge Ram

Share on:
  1. step : Removing the Wheel (0:52)
    • Loosen the 22mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Caliper (2:01)
    • Remove the 21mm bolts from the caliper carrier
    • Secure the caliper bracket and caliper with a bungee chord
  3. step : Removing the Rotor (2:27)
    • If the rotor is frozen, make sure the e-brake shoes are spun down if they're contacting the rotor
    • Tap the rotor from the front with a hammer without damaging the hub's studs
    • Pull the rotor off
  4. step : Removing the Brake Shoes (3:14)
    • Chisel off the rear retaining pin with a hammer and pick
    • Remove the two brake shoe springs with the vise grip pliers, beginning with the bottom
    • Remove the brake adjuster
    • Remove the rear brake shoe from the mechanism at the top
    • Remove the brake shoes
  5. step : Installing the Brake Shoes (5:25)
    • Be sure that the larger, single groove is on the bottom
    • Thread the upper shoe spring into the shoes
    • Place the shoes onto the hub
    • Pry out the shoes and insert them into the mechanism
    • Twist on the front retaining spring with vise grip pliers
    • Put the adjuster into place
    • Insert the lower spring in with vise grip pliers
    • Thread the retaining pin into the brake shoe
    • Lock the pin onto the holder
    • Repeat the steps on the opposite side
  6. step : Reinstalling the Rotor (9:12)
    • Remove surface rust or scaling from the hub with a wire brush
    • Apply brake grease to the hub without touching the studs
    • Insert the rotor into place
    • Apply brakes parts cleaner to the rotor
    • Put your truck in neutral
    • Check that the rotor spins freely - a little resistance is ok
    • Adjust the e-brake shoes with the star wheel if needed
  7. step : Reinstalling the Caliper (11:35)
    • Remove the bungee chord from the caliper
    • Insert the caliper into place
    • Tighten the two 21mm bolts into the caliper bracket
    • Torque the 21mm bolts to 100 foot-pounds
  8. step : Reinstalling the Wheel (12:19)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video we are going to show you how to install or replace the parking brake shoes and hardware in this 2008 Dodge Ram 1500. This one's a 2008, but the procedure is pretty much the same for 2007 to 2010 Dodge Ram 1500s, excluding mega cabs.

You'll need a new parking brake shoe and a hardware kit from 1AAuto.com, twenty one and twenty two millimeter sockets with a ratchet and extension, breaker bar, chisel, hammer, locking, needle nose pliers, flat blade screwdriver, wire brush, brake cleaner, brake grease, torque wrench, a jack, and jack stands.

Put the vehicle on the ground. Using a twenty two millimeter socket and breaker bar, break the lug nuts for your wheel loose. These chrome lug nuts tend to be swollen, so make sure your socket's on there good. Once your lug nuts are loose, raise and support the vehicle with a jack and jack stands. This wheel and tire assembly, being a big off-road tire and twenty-inch wheel, it's going to be really heavy, so we're only going to bring it up a little bit when we take it off. Remove the wheel and tire from the hub.

Remove the caliper carrier and caliper as an assembly using a twenty one millimeter socket and breaker bar. Remove the caliper bracket and caliper. Secure it out of your way using a bungee cord.

Our rear rotor is frozen onto the hub in the rear axle. You'll want to make sure that your E-brake shoes are spun down if they are contacting the inside of the rotor. In this case, ours aren't touching, so we're going to hit the sides to free the inner brake shoes from the hat of the rotor as well as the front to free it from the hub being careful not to hit and damage the studs. While hitting it head on might seem counterproductive, the shock will break all the rust loose around the center and the wheel studs.

Remove the two clips securing the E-brake shoes onto the retaining pins. We're going to use the chisel and the hammer to try to tap them up and off of the pins. Using a pair of needle nose vice grips, latch on to the lower spring. You want to get on there nice and tight, because these are under some tension. Try and hold the shoe into place and release the hook of the spring from the bottom of the shoe. Use the same process to remove the larger front spring at the top. We don't have to fully remove that as long as it's disconnected for right now to take that tension off.

Spread the E-brake shoes and remove the adjuster wheel. Pry off the shoe from the mechanism at the top. You want to try to get it off and forward. Wiggle that out of the spring. Remove the opposite side. The springs get a little bit hung up there on the way up.

Here we have our old parking brake shoes and hardware that we removed from the truck and our new parts from 1AAuto.com. As you can see, all of our parts are exactly the same. We have some longer ears on the adjuster that aren't going to affect anything, as well as some different retaining clips to hold the shoes down onto the backing plate. Also, not a big deal, just a different style. They are still the same dimensions and will go right in.

Be sure when installing the new E-brake shoes the larger groove is on the bottom. This groove and the half-moon slot sit into the top. While there is a top and bottom to these shoes, there is no front and rear.

We're going to hook through our spring from the front here this spring sits on the rear. You're going to want the long end of the spring to sit forward toward the front of the truck. I'm going to set our brake shoes over the hub. Pry out and reinstall them onto the mechanism at the top. The spring that faces out toward us is going to go in the same way with this longer part of the spring going toward the front of the truck. Sits into the same grooves as the one we have just installed on the rear. Get on there nice and tight with your pair of needle nose vice grips. Quite a bit of tension on these. You may only get it set part way on there, at which point you'll just want to use like a pry bar. Just pop it in into the channel.

Spread the bottom of the brake shoes, and install the adjuster as you see here with the star wheel facing the front of the truck. Be sure that it sits fully into the large groups at the bottom. Install the lower spring as you see here. Hook one side in. Set the other end into place with your needle nose vice grip. Again, you may only get this to install partially, at which point you'll want to use the end of your grip or screwdriver to pop the hook into place.

We're going to install these retaining pins into the back of the backing plate, so it's just going to be a little difficult for you to see once it's in the vehicle. You're going to set these over the pin. Press down on the end of this spring clip and rotate it ‘til the pin locks into that groove. There's a small hole here in the back of the backing plate as well as on the opposite side where we'll install our retaining pin through there and through the corresponding holes in our brake shoe. You're going to want to get your finger to hold that in place. Send the spring clip in and lock it down onto the other side. Repeat this step on the opposite side.

Using the small wire brush, remove any surface rust and scaling from the hub and the hub center before reinstalling your rotor to make sure that it sits on there flat and doesn't rust back on to the hub.

Install your rotor onto the hub backwards and spray it down with some brake parts cleaner. This will remove the Cosmoline coating that's put on brake rotors at the factory to keep them from rusting in storage. Be sure to get the inner edge here, because that's where our parking brake shoes are going to ride. Put some brake grease onto the tip of your finger and coat the contact surface of the hub. Be sure to keep this grease off of the threads on your studs, otherwise it can affect your wheel torque when we reinstall the wheel. Just a thin coating is fine. This is just to keep corrosion from building up to make sure that our brake rotor comes off easily next time we have to replace our brakes.

Carefully install your rotor, and clean that surface down with some more brake parts cleaner. Put your truck in neutral and make sure that the rotor spins freely. Ours is going to have a little bit of resistance to it because we have what's called the positive traction rear end, which locks the axles together and keeps both rear tires in the truck turning together. While it does take a little bit of force to move, it moves nice and smooth and you can hear a very light dragging of the parking brakes shoe against the inside of the rotor, which is just how we want it. If you do have to adjust your E-brake up for whatever reason, the star wheel that we installed on the bottom can be accessed through this rubber plug, which you can remove from the back. That will allow you to rotate it to push the brake shoes out closer to the inside of the rotor as necessary.

Remove whatever you used to secure your brake caliper and carrier assembly out of the way. Slide it back onto the rotor. Reinstall your two twenty-one millimeter bolts into the caliper bracket. You can use the socket and ratchet if you need to to get them down tight. Ours is going in nice and smooth by hand, so we'll just bottom them out and tighten them. Its a hundred foot pounds with twenty-one millimeter socket and torque wrench.

Start your lug nuts by hand. Tighten the lugs as far as you can. Remember to bring the wheel down evenly and always tighten in a cross pattern. Once the lugs are as tight as you can get them with the tire in the air, put partial weight of the vehicle on the ground by lowering it off your jack stands. Torque your lug nuts to a hundred and thirty five foot pounds in a cross pattern.

Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Chisel
  • Hammer
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Brake Parts Cleaner

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 21mm Socket
  • 22mm Socket

2009 - 2010  Dodge  Ram 1500 Truck
2007 - 2008  Dodge  Ram 1500 Truck
2007 - 2009  Chrysler  Aspen
2007 - 2009  Dodge  Durango
2002 - 2006  Dodge  Ram 1500 Truck
2003 - 2009  Dodge  Durango
2007 - 2010  Dodge  Ram 1500 Truck
2004 - 2007  Ford  E150 Van

Parking Brake Shoe Hardware Kit

Ford Dodge Chrysler Rear Parking Brake Shoe Hardware Kit DIY Solutions

This part replaces:

  • Dorman HW7329
  • DIY Solutions BFS01516
How To Replace Front Struts 07-13 Chevy Silverado

How To Replace Front Struts 07-13 Chevy Silverado

Watch this video to learn how to fix a sagging or loose suspension. The experts at 1A Auto show how to replace the front shocks in your 07-13 Chevy Silverado or GMC Sierra with pre-loaded struts.

Search Videos
Go To Top

FAST & FREE
SHIPPING

Same Day Shipping

In stock orders ship same day when ordered by 2pm ET. Need your part faster? Choose expedited shipping at checkout.

QUALITY
AUTO PARTS

Guaranteed to Fit

Our team of auto experts work hard to provide you with the highest quality, direct fit replacement auto parts. We know not all auto parts are created equal. This is why we enforce a strict level of product standards and sourcing with every part.

EXPERT USA
CUSTOMER SUPPORT

USA Customer Support

Our goal is to exceed our customers' expectations every day. We are a team of passionate auto enthusiasts who are here to help. If you have a question about our parts or a repair contact us.

HOW-TO
VIDEOS

Instructional Video Library

Our 1A Auto Video Library has thousands of how-to auto repair installation videos specific to year, make and model. Each video guides you with step-by-step instructions to empower you to tackle your own repairs on your car, truck, SUV, or van.

Loading...