Menu

1A Auto Video Library
Our how-to videos have helped repair over 100 million vehicles.

How to Replace Master Power Window Switch 04-10 Toyota Sienna

Share on:

How to Replace Master Power Window Switch 04-10 Toyota Sienna

Created on: 2013-03-08

Watch this video and learn how to replace the master power window switch on your 04-10 Toyota Sienna. 1AAuto shows you how to do it yourself!

  1. step 1 :Removing the Master Window Switch
    • Open the armrest door
    • Remove the Phillips head screw from the door pull
    • Pry off the door pull by hand
    • Disconnect the window switch wiring harness
    • Remove the Phillips screw from the front window switch tab
    • Pull off the window switch tab
    • Remove the two Phillips screws from the back of the window switch
    • Pull the switch out of the door pull
  2. step 2 :Installing the New Window Switch
    • Push the new switch into the door pull
    • Start the back two Phillips screws into the window switch
    • Put the tab back into place
    • Insert the Phillips screw into the tab
    • Tighten the back two Phillips screws
    • Connect the wiring harness to the window switch
    • Push the door pull into place
    • Insert the Phillips screw into the door pull

Tools needed for replacement

  • Screwdrivers & Related

    Phillips Head Screwdriver

Installation Video
Watch video

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the front power window switch on this 2008 Toyota Sienna. It's pretty much the same as a 2004 to 2010 Sienna. The only tool you'll need is a Phillips screwdriver.

To remove your window switch, pull up here, and there's a screw right here to remove. Once you have that screw removed, work your fingers underneath and pull up firmly on there. Pull this up, slide it back, and this all comes out. Your harness connects right here. There's a tab right here. Pushing on the tab, just pull back on the plastic. You don't want to pull on the wires. Pull back on the plastic. See how the plastic comes out and it disconnects. Pull that plastic back to make sure it actually will reset.

Now, pretty easily, three Phillips screws hold your switch in. Make sure you set this aside, the little tab, and then you've got two screws. Then your switch comes out.

The new switch from 1A Auto looks the same as the old switch and mounts the same as the old switch, but it'll work better than the old switch. A lot of times what happens, is you accidentally leave your window open, or maybe you spill some coffee, and it shorts out these switches. I'm going to put the 2 back screws in first. Just put them in a couple of threads down there. Remember this tab. Pull up the switch a little bit. Slip the tab under there. Hold the switch down. Put my third screw in. Get that in and get it nice and tight. Then I'll tighten up my other two. As I said before, make sure that's reset and pulled back. To put it in, just put a little pressure on the wires. Then put that plastic in, slide it right in and inspect it. Get the wire down in. Push that tab in, back down in. Make sure that clip's lined up, and down on. Open the arm rest. Put your screw in, and you're all set.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Tools needed for replacement:

    Screwdrivers & Related

  • Phillips Head Screwdriver

2003 - 2008  Toyota  Matrix
2005 - 2006  Toyota  Camry
2005 - 2005  Scion  xA
2002 - 2004  Toyota  Camry
2004 - 2004  Scion  xA
2004 - 2010  Toyota  Sienna

How to Permanently Attach Exhaust Flex Pipe No Clamps

How to Permanently Attach Exhaust Flex Pipe No Clamps

Watch this video to learn how to install a universal flex pipe, without using clamps. 1A Auto will show you how with a 2007 Audi A4.

Search Videos
Go To Top

Same Day Shipping

Need your part faster? Choose expedited shipping at checkout.

Guaranteed To Fit

Highest quality, direct fit replacement auto parts enforced to the strictest product standards.

USA Customer Support

Exceeding customers' expectations, our team of passionate auto enthusiasts are here to help.

Instructional Video Library

Thousands of how-to auto repair videos to guide you step-by-step through your repair.

Loading...