Menu

1A Auto Video Library
Our how-to videos have helped repair over 100 million vehicles.

How to Replace Heater Blower Motor 01-03 Chevy Monte Carlo

Share on:

How to Replace Heater Blower Motor 01-03 Chevy Monte Carlo

Created on: 2021-01-16

How to repair, install, fix, change or replace a bad or broken blower motor on 00, 01, 02, 03 Chevy Monte Carlo.

  1. step 1 :Removing the Blower Motor
    • Push in the two tabs, pull the panel down
    • Twist out the bulb socket and pull the bulb free from the socket
    • Remove the three T20 Torx screws from the blower motor
    • Push the tab on the blower motor harness and disconnect it
    • Disconnect the clip from the vacuum hose with a flat blade screwdriver
    • Push the harness to the side and pull the blower motor down and out
    • Disconnect the cooling tube
  2. step 2 :Installing the New Blower Motor
    • Feed the blower motor into place
    • Replace the three T20 Torx screws
    • Reconnect the cooling tube to the blower motor
    • Reconnect the blower motor harness
    • Replace the clip on the vacuum hose
    • Push the bulb into the socket
    • Twist the socket into the panel
    • Clip the panel into place

Tools needed for replacement

  • General Tools

    Flashlight

  • Star Drivers & Sockets

    T20 Driver

Installation Video
Watch video

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the Blower Motor on this 2003 Chevy Monte Carlo. It's the same part and similar process on this Monte Carlos from 2001 to 2003.The items you'll need of this is a new Blower Motor from 1AAuto.com, a T20 Torx Driver and a flashlight.

Start off by just pushing in these two tabs, you can see we're missing one, but you just push them in and pull the panel down, twist out the socket, and just pull the bulb free. Your blower motors right here, and it's held in with three T20 Torx bolts. We'll just fast-forward as Mike removes those. Now, reach back, find the harness, pull it forward, and just push the tab on the harness and disconnect it. Then, using a flat blade screwdriver, pry open on this clip, push that harness all away aside, and pull the blower motor down and out. Then just disconnect this hose, pull your harness through it, and then just remove the rest of the hose from the other end.

On the left is the blower motor you've removed; on the right is the new one from 1A Auto. The one we removed was already replaced, so you probably won't see that pigtail if you have an original motor in your car. It might change how you disconnect the blade just a little bit. Our new one from 1A Auto though, on the other hand, is just like the original, and will bolt in place and hook back up to the original harness no problem. Now, to make it easier to put the new blower motor in, you want to just pull out on this clip. Now, push the blower motor up into place. Just pull that harness aside.

Then replace those three T20 Torx screws. We'll fast-forward here as I put those in. I do start the first two that are easier to get to first. Put them in by hand and a few turns. Actually, I tighten them up snug with the driver, and that makes it easier to get the third one in and then tighten them all up. Reconnect the hose back, and then reconnect it to your blower motor, and put this loop back around the blower motor. Then find your harness and reconnect it. Now, put this clip back into place, put your harnesses back into the clip, and then just re-clip it. Push the bulb back into your socket, twist the socket back into this panel, feed the panel back, and then push up into place. You're all set.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Tools needed for replacement:

    General Tools

  • Flashlight

  • Star Drivers & Sockets

  • T20 Driver

2000 - 2002  Oldsmobile  Intrigue
2001 - 2003  Chevrolet  Monte Carlo
2001 - 2003  Pontiac  Grand Prix
2000 - 2005  Buick  Century
2000 - 2004  Chevrolet  Corvette
2000 - 2004  Buick  Regal
2001 - 2003  Chevrolet  Impala
2000 - 2003  Pontiac  Grand Prix
2000 - 2002  Chevrolet  Corvette
2001 - 2002  Chevrolet  Monte Carlo
2003 - 2003  Chevrolet  Monte Carlo

Heater Blower Motor & Resistor Kit

Chevrolet Buick Pontiac Olds HVAC Blower Motor Kit DIY Solutions HVA03326

Part Details:

  • Highest Quality Materials
  • Direct Fit Replacement - Guaranteed to fit and function for your specific application
  • (1) Heater Blower Motor
  • (1) Heater Blower Motor Resistor
  • Quality Tested - built to a strict level of product standards.
How to Remove a Stuck Brake Bleeder Screw

How to Remove a Stuck Brake Bleeder Screw

Watch this video to learn how to remove a brake bleeder screw that’s stuck or rusted on. The experts at 1A Auto will show you how to loosen a stuck screw and bleed your brakes.

Search Videos
Go To Top

Same Day Shipping

Need your part faster? Choose expedited shipping at checkout.

Guaranteed To Fit

Highest quality, direct fit replacement auto parts enforced to the strictest product standards.

USA Customer Support

Exceeding customers' expectations, our team of passionate auto enthusiasts are here to help.

Instructional Video Library

Thousands of how-to auto repair videos to guide you step-by-step through your repair.

Loading...