How to Replace Headlights 2004-06 Chrysler Pacifica
Created on: 2012-11-08
Watch this video to learn how to replace and service the headlight assembly and bulbs on your 04-06 Chrysler Pacifica.
-
step 1 :Removing the Headlight Assembly
- Remove the two 8mm bolts at the top of the headlight.
- Push the bumper cover down and reach underneath the light and pull on the light.
- Remove the headlight assembly.
- Push the thumb tab on the harness attached to the headlight assembly and disconnect.
-
step 2 :Changing the Headlight Bulbs
- Remove the rubber cover.
- Reach in and twist the light counterclockwise.
- Pull the bulb out.
- Replace it and avoid touching the glass part.
- Insert the light and twist clockwise to lock it.
- The other bulbs need to be twisted counterclockwise to remove and replace the bulbs.
-
step 3 :Replacing the Headlight Assembly
- Remove the clip from the old headlight assembly by pressing the tabs and pulling it through.
- Put the clip onto the new harness on the new headlight assembly.
- Clip the harness in place.
- Connect the headlight harness
- Line the headlight up and push it into place.
- Replace the two 8mm bolts at the top of the headlight.
-
step 4 :Adjusting the Headlights
- Park 20' from a wall on a flat surface.
- Turn the adjusting bolt clockwise to aim the light down and counterclockwise to angle it up.
- The low beam concentration should be 1" lower than the bulb.
- The high beam concentration should be at the same height as the bulb.
Tools needed
-
Socket Extensions
8mm Socket
Ratchet
Brought to you by 1AAuto.com your source for quality replacement parts and the best service on the internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out and next time you need parts for your vehicle think of 1AAuto.com. Thanks. In this video we're going to show you how to service headlights on this Chrysler Pacifica. We're going to show you both if you need to change bulbs as well as if you want to replace the entire assembly because your lights are clouded or faded. The only tool you'll need is an 8mm wrench or a socket and ratchet. If you need to adjust your headlights you'll need a socket ratchet with extension.
Okay what we have here is a before picture. Here's our vehicle left hand headlight before and then here's after. The car has about 130,000 miles on it. The new light just makes it look that much better and that much fresher and that much newer. Okay just open up the hood by pulling on this lever and right under here a little yellow lever that you push towards the left. Pull the hood up. There's a rod right here that comes up. Okay the top of each light there are two 8mm bolts. You can actually use an 8mm wrench or socket and ratchet like this is the best. You could use a flat blade screwdriver, but that would probably be a little more difficult. Remove these bolts. Okay probably the most uncomfortable part about the whole thing, push your bumper cover down and reach underneath and pull out on the light. Then you can let that go and then hold the inside of the light out first and the whole light comes out.
As you pull the light out you'll see a connector right here. You press firmly on this tab with your thumb and disconnect. If you're just looking to change a bulb you take one of these covers off and then way down in there is the bulb. You just reach in, twist counterclockwise and pull it out. Okay and then your bulb comes off by prying out and pulling. Okay, new bulb goes on. Do your best not to touch the bulb surface. If you touch it wipe it with a clean cloth. Okay. Reach back in. Okay there's also a bulb right here. It might be good to have a pair of pliers around. Reach in there again, twist counterclockwise. Okay, again that bulb just pulls straight out. Put it back in turn it clockwise to lock it.
Okay if you're putting on a new headlight you'll want to save this clip. Use a small screwdriver and you've got to press in on the tabs, pull it from the backside. That didn't pull through the way I wanted it to. Okay, the clip pulls through and to get it out of here you just take your small screwdriver, put it right in there, pry them apart and slide that back out. Okay. New light from 1A Auto. Nice, clear, bright. Okay, take our clip. Take our harness connection slide this clip in and then bring this right up and clip it. Put it on like that. Okay, bring it in, reconnect the harness. Make sure you hear it click. Then you want to put the light in, peel back the plastic here some and take it right off. Okay. Put it in and this part of the plastic up here should go up on top of the fender and then kind of let the light go in and then it should clip in place. Just put your two bolts back in the top. Tighten them up.
If you need to adjust your headlight there's an adjuster right here. Okay. Turning it counterclockwise moves the headlights up. Clockwise moves them down and you basically want to line your headlight up so that at 20 feet away from a wall on a flat surface your low beam should be 1 inch below the height of the bulb. So, if your bulb is say 26 inches high your low beam should be shining on a wall 20 feet away at 25 inches. The middle of the concentration of the beam. Your high beam is basically the same but it should be pointing level. So, on a level surface 20 feet away from a wall the concentration of the beam should be the same level as the height of the bulb.
We hope this helps you out. Brought to you by www.1AAuto.com your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free at 888-844-3393.We're the company that's here for you on the internet and in person.
Shop Products
Chrysler Pacifica Driver Side Headlight Assembly TRQ HLA74109
Part Details:
- Yes
- Assembly
- PC (Polycarbonate)
- Yes
How to Replace Headlights 2007-14 Chevy Suburban 1500
Watch this video to learn how to replace and service the headlight assembly and bulbs on your 07-14 Chevy Suburban 1500.
