Menu

1A Auto Video Library
Our how-to videos have helped repair over 100 million vehicles.

How to Replace Front Sway Bar Bushings 94-10 Dodge Ram 1500

Share on:

How to Replace Front Sway Bar Bushings 94-10 Dodge Ram 1500

Created on: 2016-08-04

Watch this video to learn how to replace the front sway bar bushings on your 94-10 Dodge Ram 1500.

  1. step 1 :Removing the Sway Bar Bushings
    • Remove the two 15mm bolts from each sway bar bracket
    • Pull off the sway bar brackets
    • Cut the bushings open with a utility knife if necessary
    • Pull off the bushings
  2. step 2 :Installing the Sway Bar Bushings
    • Push the bushings onto the sway bar
    • Put the sway bar brackets into place
    • Insert the two 15mm bolts into each sway bar bracket
    • Tighten the four 15mm bolts to 45 foot-pounds of torque

Tools needed for replacement

  • General Tools

    Utility Knife

  • Ratchets & Related

    Socket Extensions

    Torque Wrench

    Ratchet

  • Sockets - Metric

    15mm Socket

Installation Video
Watch video

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the front sway bar bushings in the 2008 Dodge Ram 1500. Here are the items you'll need for this repair.

To replace the front sway bar bushings, you're going to undo these two brackets. Each one has two 15mm bolts. We're going to use the 15mm deep socket. You could also use a short socket and extension and a ratchet. The reason we're doing this job on the ground is because jacking it up and allowing the suspension to hang will put load on the sway bar, making it more difficult to line up these brackets and bolt them into place. Remove the bracket and repeat these steps on the opposite side. To remove the bushing from the bar, find where the bushings split from the factory. Our bushings here have either been glued together for some reason or just corroded, built up with gunk and stuck together over all the years they've been on this truck. We're going to use a razor blade to open up the factory slot that was in them. Remove them from the sway bar.

Here we have our old sway bar bushings that we removed from the vehicle and our new sway bar bushings from 1A Auto. You probably can't tell, but this is what these used to look like. See that they're all worn out. They’ve got some rust scaling in here. The rubber is corroding and falling apart. We've actually rubbed a hole completely through over here. It's not going to sit on our sway bar right and it's going to allow it to move up and down inside of this bore, which is going to create some noises and handling issues. This new sway bar bushing from 1A Auto, you could see is nice and round with nice thick rubber. It's going to fit our sway bar nice and tight and insulate it from any noise or vibration that we may have, especially from this. While this particular one is blue, they do come in a variety of colors just based on the manufacturing and what color rubber they decide to use. It's going to go on direct fit just like your original equipment and fix you up right.

We'll split the bushing and install it over our sway bar. This gap may not close fully. That's fine. The new bushings are much firmer than the old ones, obviously because the rubber is much thicker. It hasn't been worn away and deteriorated by chemicals and road grime. Line them up and reinstall the bracket onto the bushing. Start your two 15mm bolts. Do the same thing over here. Don't be afraid to tap that bracket on a little bit. Once both brackets are one and all four bolts have been started, go ahead and tighten them down with your 15mm socket and ratchet. Torque these bolts to 45 foot-pounds.

Thanks for tuning in. We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Tools needed for replacement:

    General Tools

  • Utility Knife

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet

  • Sockets - Metric

  • 15mm Socket

1994 - 2010  Dodge  Ram 1500 Truck
2005 - 2005  Dodge  Dakota
2011 - 2012  Ram  2500 Truck
2011 - 2012  Ram  1500 Truck
1994 - 2009  Dodge  Ram 3500 Truck
1994 - 2010  Dodge  Ram 2500 Truck
2006 - 2009  Dodge  Ram 2500 Truck
2006 - 2008  Dodge  Ram 1500 Truck
2006 - 2009  Dodge  Ram 3500 Truck
2009 - 2010  Dodge  Ram 1500 Truck
2002 - 2005  Dodge  Ram 1500 Truck
2006 - 2007  Dodge  Ram 1500 Truck
2011 - 2018  Ram  1500 Truck

02-07 Dodge Ram 1500 P/U 2WD w/32 mm SB Front Sway Bar Link and Bushing Kit

Dodge Ram 1500 4 Piece Suspension Kit TRQ PSA63636

Part Details:

  • (2) Front Sway Bar Links
  • (2) Front Sway Bar Frame Bushings
  • Improved ride comfort and longer life
  • Direct fit - easy install, pre-greased, no maintenance required
  • No modifications, all the parts needed in one kit
  • 4 Piece
What NOT to Do When Replacing a Window Regulator

What NOT to Do When Replacing a Window Regulator

If you made a mistake, and your window regulator cable jumped out at you, check out this video to learn some tips on how to get it all back together!

Search Videos
Go To Top

Same Day Shipping

Need your part faster? Choose expedited shipping at checkout.

Guaranteed To Fit

Highest quality, direct fit replacement auto parts enforced to the strictest product standards.

USA Customer Support

Exceeding customers' expectations, our team of passionate auto enthusiasts are here to help.

Instructional Video Library

Thousands of how-to auto repair videos to guide you step-by-step through your repair.

Loading...