Menu

1A Auto Video Library
Our how-to videos have helped repair over 100 million vehicles

How to Replace Front Door Window Regulator 09-18 Ram 1500

Share on:
  1. step : Removing the Outer Door Panel (0:25)
    • Pry off the sail panel
    • Remove the six T20 Torx bolts from the perimeter of the door panel
    • Pry out the trim door behind the door handle
    • Remove the Phillips screw from behind the door handle
    • Pry the master power window switch up with a flat blade screwdriver
    • Pry the wiring harness out of the switch panel
    • Pry out the plastic grommets from the perimeter of the door panel
    • Lift the outer door panel up and off
  2. step : Removing the Inner Door Panel/Window Regulator (2:36)
    • Remove the twelve 10mm screws from the perimeter of the inner door panel
    • Remove the four 5mm screws from the speaker
    • Pull the speaker out
    • Disconnect the speaker wiring harness
    • Pry out the rubber door
    • Connect the power window switch
    • Adjust the window so you can access the clip
    • Press the clip to release the glass from the window regulator
    • Lift the window up and secure it with painter's tape
    • Disconnect the power window switch
    • Pry the clips on the wires from the door with needle nose pliers
    • Disconnect the wiring harnesses
    • Unclip the clips from the door handle latch and lock rods
    • Remove the three T30 Torx bolts from the door latch
    • Pull the interior door panel away from the door
    • Remove the interior door panel
    • Disconnect the door lock actuator wiring harness from the door lock actuator
    • Pull the rubber grommet through the door panel
    • Remove the inner door panel
  3. step : Installing the Inner Door Panel/Window Regulator (9:16)
    • Feed the door lock actuator wiring harness behind the window track
    • Connect the wiring harness to the door lock actuator
    • Press the grommet into the inner door panel
    • Slide the inner door panel into place
    • Tighten the T30 Torx bolts to the door lock actuator
    • Clip the door handle latch and lock rods
    • Connect the wiring harnesses
    • Press the clips on the wires to the door
    • Lower the window down
    • Clip the window to the window regulator
    • Press on the rubber door
    • Connect the speaker wiring harness
    • Insert the speaker into place
    • Tighten the four 5mm screws to the speaker
    • Tighten the twelve 10mm bolts to the perimeter of the inner door panel
  4. step : Installing the Outer Door Panel (14:35)
    • Lift the outer door panel into place
    • Press the grommets into the outer perimeter of the door panel
    • Connect the wiring harness to the window switch
    • Press the window switch into place
    • Tighten the Phillips screw behind the door handle
    • Press on the door handle trim
    • Tighten the six T20 Torx bolts around the perimeter of the door panel
    • Press on the sail panel

Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!

We'll open up the door. And we are going to start off by coming up here and removing this cover. You can just put your hands behind it, kind of pull up. And you can see there's a push pin here, and a push pin here, and then there's two little hooks that hook into the door panel itself. Around the perimeter of the door panel are six T-20 torx bolts, and they're actually made of plastic, which is a little strange. We'll go all around the door panel, and we'll start pulling these out. Being that they're plastic, they don't come out like a normal screw does. You have to be very gentle, and almost pull on them as they unscrew. Here we go.

Right here, behind the door panel, is a secret cover that you can pop off with a flat-tip screw driver. And you can see, you want to grab it from the top, and go down, and then behind that is a Phillips head screw. So now, we'll use a Phillips head screwdriver to remove the Phillips head screw. For the power window switch, we'll just slide a little screw driver in here. It pops out super easy. And we'll pop up this little safety pin. Here we go. And then you can push the tab down and pull the connector out.

These little anchors here, they need to come out of the door panel because we need to lift it up. We just lost one. Now we'll do the upper one, and there's the second one. So we'll go all the way around the door, and pop those out. And then all we have to do is lift straight up on the door panel, and it should come off. Around the perimeter of this inner plastic door panel, there's about twelve 10mm bolts that we want to remove. So we're going to go ahead and get started. Using a 10mm socket and a ratchet. Once you get them started, you can probably just pull them up by hand.

Here we have the speaker, and you can see there's four 5 millimeter screws holding it on so we're go ahead and use a five millimeter socket and an extension because I love extensions and a quarter drive ratchet to remove this. All right. Now you can pull your speaker out.

On the backside of the speaker you have one connector that you can push down the tab of and pull it right out. And there you are. Now it's completely removed from the door. All right, behind this sort of secret door here you'll find the window regulator. And the window regulator is attached to the glass by this clip. So what you might need to do is attach your power window switch and adjust your window up or down so that you can get this right here.

So you might need to put the key in the ignition and then adjust the window up or down because you want to be able to push this little clip right here and release the glass from the window regulator. And the same thing applies over here in the speaker hole. You want to move the window regulator down until the glass is right in front of the speaker hole. All right the glass is held in on this clip and there's little push tabs here. You can see you can push it in with a flat tip screwdriver. There's another one on the inside here. And if you push both of those up like so, the glass will be released from the regulator and you can do this on this rear one and on the front one in the speaker hole.

You're probably going to want a second person to hold the glass up so that it doesn't fall down in the door and either injure you or break the glass. Now we should be able to lift this glass right up and you can do a couple different things with this. What I like to do is just get some tape, and I'll tape the tape to the glass on both sides and up and over the top and that'll hold the glass in place. The other option is to remove some of the trim at the top and you can pull the glass right out of the door.

It's a little bit more work, more work than I want to do. And probably more work than you want to do. So it's best to just get some good tape and put a bunch of tape all over the window. Once you have your glass set in place, you can go ahead and remove your power window switch and that way your window regulator won't move around unexpectedly. And you can pull your key out of your ignition.

Now we're going to start removing all of the wires from the plastic panel in here. There's the first one. Can use needle nose pliers to get that. This one you can use a trim panel tool or you could probably just pull on it. Over here there's a couple of little tabs that you push down to get these connectors. See? This is the tab you want to push down. And there's the second one. So now the mirror's disconnected.

So now we'll go to this. We'll use our trim tool again and follow it along. Down here we got the speaker and this sensor. This also has a push tab on it. Over here we need the trim panel tool again. All right. Then we need to do the power window motor by pushing the tab on that connector. And then up here we'll disconnect these three connectors at the module by pushing the tabs on those.

Up inside this access panel there's two little clips that attach your door handle and your lock to your door latch. And we need to remove those. They actually function the same exact way as the door handle clip where you'll just kind of pull it away and you can see it latches right on just like this. So I'll put back in to show you how it clips on. Just like that. That functions the exact same way.

So we're going to do that up inside the door. Next we're going to use a T-30 Torx bit to remove the door latch from the door. Once you crack these loose you can probably just you can spin them out by hand fairly easily. All right, now you should be able to pull the door panel away from the door. There we go. And drop it down behind this harness. You'll keep it all connected to the car but you can pull it out just like that.

On the top of your door latch is a connector for your door lock actuator, and you need to push the red tab back that's the safety and then pull on it to disconnect it from the actuator. And then over here on the front of the door panel, you got to pull this rubber grommet through and then you'll have it completely separate from the truck.

You'll see that this window regulator is actually built into the plastic inner door panel. This regulator isn't removable so this is all one piece and that's how you replace it. So we have to get this door lock actuator wire through the door panel so we'll feed this through. Should go behind this cable.

Behind the window regulator itself, and then behind this bracket. Right here you have a clip that you can snap into place, and then right here's another clip. And then over here at the actuator we can plug in the connector and snap the safety in. That way it won't fall out when you're installing the door.

There's also this rubber grommet in the door panel that we're going to want to push into place. All right. Okay, now with the front of this plastic panel downward, we're going to slide this in and then we're going to lift up on the front of the panel tucking it in behind all the wires. There we are. Now we're going to put these three Torx screws back into the latch. Like to get all three in loose before we tighten them up.

It's tough to see but behind here. I'm reinstalling the door handle rod and the lock rod into the door latch. Okay, now we can start putting all of the wires back in place. We'll snap the power window motor connector back in and we'll feed these wires up here. Get the blue right here and believe purple's on top and then white. And down here by the speaker we can feed these through. And then we have this one at the bottom that plugs in right here. Up here we have the mirror wiring. Snaps in right there. And then right here.

And then it plugs into the module. Now we're going to slide the glass down into the door and we're going to snap it into the window regulator. But to do that we need to remove all this tape that I have holding the window. All right, be ready for the glass to drop when you do the last piece of tape. Maybe have a friend hold it.

Okay, and then we can slide the glass back down into the door very gently until it reaches the window regulator right down here. And you can see it and hear it snap right into place. You want to make sure this side is latched, and you want to come over here in your speaker hole and make sure that this side is latched as well.

Before you put the door panel all back together again, you want to make sure your window goes up and down. So I like to plug the power window switch in and turn the ignition on. And make sure the window works. 'Cause you don't want to get everything back together then find out your window doesn't work. In this case, seems to work pretty great. All right. Now we'll turn it off and we'll unplug the window switch again. We'll plug the speaker back in right here. It's nice because the speaker has these two little tabs on the bottom that hold it in place. And I'll get all the bolts started before I actually tighten anything. Now we'll tighten these up with a five millimeter socket and ratchet.

Now we'll reinstall this little access panel cover and then we can start putting the twelve 10 millimeter bolts all the way back around this plastic panel. You want to get them all in first to make sure it's all aligned and then you start tightening them up. All right, so to put the door panel back on, we're going to slide this lock up through the hole and then we're going to feed the power window wires, power window switch wires, through this. And then kind of drop it down onto the door panel.

Now we'll plug in the window switch and drop it right into the door panel. We're now going to slide the door handle bezel behind, doing the rear section first and then snapping it into place. And then there's a large Phillips head screw that we'll slide right through here and screw in. And then there's the little access panel that will also slide in doing the bottom first. And that also just snaps right in.

And we're now at the point where we can put these door panel screws back in, and they go in just like this. Looks like I'm going to probably have the bottom piece to get it to screw in. We'll do this all the way around the door. And lastly we'll put this right back on to cover up the mirror bolts.

Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Painter's Tape

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 5mm Socket
  • 10mm Socket

  • Specialty Tools

  • Trim Tool Set

  • Star Drivers & Sockets

  • T30 Driver
  • T20 Driver


Auto Repair: How to Check/Add Power Steering Fluid to My Car or Truck

Auto Repair: How to Check/Add Power Steering Fluid to My Car or Truck

Watch this video to learn how to check the level of your power steering fluid, and add more if necessary. Some details may differ in your vehicle.

Search Videos
Go To Top


Same Day Shipping

Orders ship same day when ordered by 2pm ET. Need your part faster? Choose expedited shipping at checkout.


Guaranteed To Fit

Providing you the highest quality, direct fit replacement auto parts enforced to the strictest product standards.


USA Customer Support

Exceeding customers' expectations every day, our team of passionate auto enthusiasts are here to help.


Instructional Video Library

Thousands of how-to auto repair videos specific to year, make and model guide you step-by-step through your repair.

Loading...