1A Auto Video Library
Our how-to videos have helped repair over 100 million vehicles.

How To Replace Front CV Axle Joint 05-09 Chevy Equinox

Share on:

How To Replace Front CV Axle Joint 05-09 Chevy Equinox

Created on: 2013-03-19

Check out this video to learn how to replace a broken, worn or vibrating front CV axle joint in a 05-09 Chevy Equinox.

  1. step 1 :Removing the Wheel
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step 2 :Removing the Ball Joint
    • Have an assistant hold the brakes
    • Use a 36mm socket and breaker bar to remove the hub nut
    • Hammer the axle through the wheel to loosen it
    • Bend the cotter pin, grab hold of it, and break the cotter pin off
    • Loosen the castle nut with an 18mm wrench but don't remove it
    • Place a ball joint fork into the ball joint and knuckle
    • Hit the ball joint fork with a hammer to separate the two
    • Remove the castle nut
    • Pull the ball joint down and out
    • Pull the axle out
  3. step 3 :Removing the Axle
    • Pry the axle from the transmission with a breaker bar
    • Pull the axle out
  4. step 4 :Installing the New Axle
    • Push the axle into place
    • Pull the hub assembly back and push the axle into the hub
    • Push the ball joint up into the knuckle
  5. step 5 :Reinstalling the Ball Joint
    • Preliminarily tighten the 36mm hub nut
    • Tighten the castle nut by hand
    • Tighten the castle nut with an 18mm wrench
    • Torque the castle nut to 55 foot-pounds
    • Insert the cotter pin into the castle nut and twist it
    • Have an assistant hold the brakes
    • Torque the hub nut to 151 foot-pounds
  6. step 6 :Reattaching the Wheel
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
  7. step 7 :Testing the Brakes
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement

  • General Tools


    Jack Stands

    Floor Jack


  • Pliers, Cutters & misc Wrenches

    Lug Wrench

    Needle nose pliers

  • Ratchets & Related

    A Piece of Pipe (for leverage)


  • Screwdrivers & Related

    Pry Bar

    Flat Blade Screwdriver

  • Sockets - Metric

    19mm Socket

    36mm Socket

  • Specialty Tools

    Pickle Fork

  • Wrenches - Metric

    18mm Wrench

Installation Video
Watch video

Brought to you by, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of Thanks.

In this video, we're going to show you how to remove and reinstall a front axle. This is a 2008 Chevy Equinox, and they fit on the 2005 to 2010 Equinox, Saturn Vue, and Pontiac Torrent models. This procedure will be generally the same, and you know if you have an axle or worn CV joint, if you turn your vehicle all the way left or right, and you hear a clicking noise or feel a little feedback in the steering wheel, that's usually a good sign of a bad CV joint. You'll need a new axle from 1A Auto, jack and jack stands, a 19mm socket or your lug wrench, ratchet with a breaker bar or a pipe for some extra leverage, 36mm socket, pliers, hammer small screwdriver, an 18mm wrench, a ball joint fork, and large pry bar.

Start out by removing the front wheel. If you don't have the benefit of air tools like I have, you'll want to loosen the lug nuts while your vehicle's on the ground, then raise and securely support your vehicle. Then take your lug nuts off the rest of the way and remove the wheel.

To get this center nut off, you can try a couple things. If you don't have the benefit of impact tools, you want to have a person in the car hold the brakes while you use a 36mm socket and a breaker bar to get it off. The easiest way to do it is to just use an impact wrench, and I've got one so I'm going to use it. You don't want to beat this with a hammer, but you can just hit it once, watch the axle in relation to your wheel disk, and if it moves and it did then just use a hammer. Now you want to separate the ball joint from the steering knuckle. Possibly the most difficult part of this repair is actually just getting the cotter pin out of this bolt. Bend it up right there, and I'm just going to use pliers to grab hold of it.

I am going to break the end of the car pin right off, just by twisting back and forth. Now, I'm just using the pliers and the screwdriver and prying out the other end. What you can do, usually, the cotter pin is pretty rusted and in pretty tough shape. If you can't get it off, I was able to actually on the other side when I did the other side of this vehicle, you can just put your wrench right on that bolt and turn it, and that will shear the cotter pin off. Especially if the cotter pin's a little bit rusty. Otherwise, using the pliers, screwdriver, and maybe even a lineup tool or an impact tool to drive that cotter pin out, is what you'll need to do.

Now, you're going to want to loosen up this nut, so take an 18mm wrench, put it on there, now I'm going to take my 17mm wrench. Hook it on here for some extra leverage. As soon as it starts moving I take my box end off and just use the opening. I'll speed up here as I take that nut the rest of the way off. You want to basically take it off until it turns easily with your fingers. You do want to leave it on with a few threads so that when you separate the control arm from the steering knuckle, nothing violent happens, the nut will still hold it together.

Now with that nut still on there, I'm going to take a ball joint fork and put it right in here. Now remove that nut the rest of the way. Take our ball joint down and out. Pull the axle from the back here. Now, right underneath here is where the axle connects to the transmission. You're going to want a good long breaker bar. Put the bar up in there. Press firmly. You should have it off the axle, just pull your stuff to the side here. Pull the axle out.

Reinstallation, and no, I'm not putting a new axle on this vehicle, it actually doesn't need one. What this actually vehicle needs is a lower ball joint, so you can see our other videos for replacing that lower ball joint. I'm just doing this as I go, but you would take your new axle 1A Auto we sell the correct axles put it in, you have to guide it onto the transmission here. You'll have to pull your hub assembly aside and give yourself some room. It's a little easier with a helper.

Once you get it onto the transmission, you just kind of work it on. A couple different angles, get it on there and make sure you push it nice and firmly against it. Get it to lock on there. Pull your strut and knuckle out. Get the axle back in your hub. Turn things a little bit, get it to come back through. Pull your control arm down, get the ball joint back up into the steering knuckle.

Okay, so the axle shaft is through, and the ball joint is up and through. My axle is seated nicely here. I'm going to put my nut back on. Just kind of tighten it up preliminarily. Push the ball joint up and in, and start the nut on. Now, here, I've put a jack underneath right where the ball joint is. I'm going to lift that up a little bit, and then just kind of finger tighten the nut on the ball joint more. Not the best recording angle here, but use your 18mm wrench again, and, for the ball joint, you basically want to pull it as tight as you can with an 18mm combination wrench.

Generally, the ball joint nut should be torqued to about 55 foot-pounds, but it's really hard to get a torque wrench onto this spot, so pulling it as tight as you can and then pulling it to a point where you can get the cotter pin through and lock the nut in place is the best procedure. Here, I'm just pulling the ball joint just a little bit tighter, so it's a nice clear path through to get the cotter pin in. Put the cotter pin in, pull it through, and then bend it so it won't come out. I've got a person in the car holding the brakes, and I'm going to torque these to 151 foot-pounds.

Now we can put the front wheel and tire back on, and I'll just thread the lug nuts on by hand a few turns first. Make sure they're going on correctly, and then just preliminarily tighten them with my impact wrench. Torque your lug nuts to 100 foot-pounds.

Any time you've done extensive work to the front end of your car, just hit the brakes, pump them up, make sure the pedal's nice and firm. Move your wheel back and forth, feel for any clunks, and listen outside the car. Make sure everything seems pretty tight.

Then just test drive it, but go easy at first. A couple stops in the driveway, turn in the driveway, and then try a prolonged test drive.

We hope this video helps you out. Brought to you by, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Floor Jack
  • Assistant

  • Pliers, Cutters & misc Wrenches

  • Lug Wrench
  • Needle nose pliers

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 19mm Socket
  • 36mm Socket

  • Specialty Tools

  • Pickle Fork

  • Wrenches - Metric

  • 18mm Wrench

2004 - 2007  Saturn  Vue
2006 - 2007  Saturn  Vue
Search Videos
Go To Top

Same Day Shipping

Need your part faster? Choose expedited shipping at checkout.

Guaranteed To Fit

Highest quality, direct fit replacement auto parts enforced to the strictest product standards.

USA Customer Support

Exceeding customers' expectations, our team of passionate auto enthusiasts are here to help.

Instructional Video Library

Thousands of how-to auto repair videos to guide you step-by-step through your repair.