Menu

1A Auto Video Library
Our how-to videos have helped repair over 100 million vehicles.

How to Replace Blower Motor 97-01 Toyota Camry

Share on:

How to Replace Blower Motor 97-01 Toyota Camry

Created on: 2016-06-22

New Heater Blower Motor with Fan Cage from 1AAuto.com How to repair, install, fix, change or replace a bad or broken blower motor fan speed resistoron 97, 98, 99, 00, 01, Toyota, Camry

  1. step 1 :Removing the Blower Motor
    • Pull the lower cover from the glove box straight down
    • Disconnect the blower motor electrical connector
    • Remove the three screws that hold the blower motor with a flat blade screwdriver
    • Remove the blower motor
  2. step 2 :Installing the Blower Motor
    • Insert the blower motor into place
    • Tighten the three screws to the blower motor
    • Connect the blower motor electric connector
    • Insert the lower cover to the glove box

Tools needed for replacement

  • Screwdrivers & Related

    Flat Blade Screwdriver

  • Star Drivers & Sockets

    T25 Driver

Installation Video
Watch video

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the A/C and heater, lower motor. This is a 1998 Toyota Camry, which is the same for 1997 to 200. You'll need a new blower motor from 1AAuto.com and a flat blade or a T25 Torx driver.

Remove the lower plastic cover onto the passenger side of the dashboard by pulling straight down and toward you. Remove the electrical connector at the bottom of the blower motor. Remove the three screws, holding the blower motor into the HVAC housing. This can be done with a Torx bit, a 10 millimeter socket or a flat blade screwdriver which we'll use. Remove the blower motor from the bottom of the HVAC housing.

Here we have our old part that we removed from the vehicle and our new part from 1A Auto. As you can see, there are some slight aesthetic differences in the actual fan, but it's still going to function properly.

We have the same mounting locations, the same 2-pin connector, and the same outer diameter to fit into our HVAC box so if your heat and A/C isn't blowing like it used to, or you hear a noise when you run your fans. This new part from 1A Auto is going to fix you up right.

Reinstall the blower motor into the HVAC box. Reinstall your three screws and either a Torx bit, a 10 millimeter, or a flat blade screwdriver.

To show you that this hardwood can be installed with three different tools, we're going to use a T25 Torx screwdriver to reinstall the hardware. Reinstall the electrical connector.

Install the rear pin into the hole by the firewall and snap the front clips into place.

Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.

Tools needed for replacement:

    Screwdrivers & Related

  • Flat Blade Screwdriver

  • Star Drivers & Sockets

  • T25 Driver

1997 - 2001  Toyota  Camry
1999 - 2003  Toyota  Solara
Search Videos
Go To Top

Same Day Shipping

Need your part faster? Choose expedited shipping at checkout.

Guaranteed To Fit

Highest quality, direct fit replacement auto parts enforced to the strictest product standards.

USA Customer Support

Exceeding customers' expectations, our team of passionate auto enthusiasts are here to help.

Instructional Video Library

Thousands of how-to auto repair videos to guide you step-by-step through your repair.

Loading...