How to Remove Washer Fluid Pump 2009-18 Ram 1500
Created on: 2018-06-11
How to repair, install, fix, change or replace a broken, damaged, or failing windshield washer pump on 16 Ram 1500
-
step 1 :Removing the Grille
- Pry up the push clips from the radiator shield with a pry tool
- Remove the shield
- Remove the 10mm bolts from the grille
- Press in the clips with a flat blade screwdriver
- Insert a trim tool underneath the grille to release the clips
- Remove the grille
-
step 2 :Removing the Washer Reservoir Pump
- Disconnect the washer pump connector
- Have a drain pan ready
- Remove the washer pump hose with a 90 degree pick
- Pull the pump out, up, and off
-
step 3 :Installing the Washer Reservoir Pump
- Insert the washer pump into place
- Connect the hose to the washer pump
- Connect the electrical connector
-
step 4 :Installing the Grille
- Line the tabs on the grille with the slots on the vehicle
- Press the grille into place
- Tighten the 10mm bolts to the grille
- Insert the radiator shield into place
- Press the push-pins to the cover
Tools needed
-
Socket Extensions
Flat Blade Screwdriver
10mm Socket
Ratchet
Pick
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
In this video we're going to be removing and installing a washer pump in a 2016 Ram 1500 pickup. If you need parts for your vehicle, click the link in the description and head over to 1aauto.com.
We're going to open the hood right under your steering wheel. This little lever pops the hood. The hood safety latch is right here. I'm going to pull it to the left and pull up. We're going to pull this panel off. There's some clips. You're going to use a clip tool to get underneath here. There's one over here too. It's easier if you go under it and pry up on it. You could go underneath the clip and pry, but sometimes you break the clip, so we'll just go underneath it and pry up. Pry that up, and then we just pull this off and pull it out of the way.
We're going to take these four bolts out right here. They're 10 millimeters. We use a 10-millimeter socket and a ratchet. So down here, there's a clip that holds it in. I'm going to use a flat blade screwdriver. These clips sometimes break, so just be careful. Just pop it out like that, and there's another clip further down. You can't see it. And then on the other side is the same. Clip right there. Pull that out.
Then we're going to use some trim tools. We actually sell these at 1AAuto.com. We're going to go under here. You want to be careful not to scratch the paint. But there is some of the retainers under here. And I'll show you these better once the grille is out. Okay, right there. Well, and then we're going to grab on the grille and pull forward, release that one. There's one over here as well, and then there's also one in the middle. Go ahead and release this, and then there's one more in the middle here. The whole grille comes out.
To get this pump out, we're going to remove this wire over here. Pull that out. We'll disconnect the connector right here. Just put the tool in there, and that flat blade tool, pry that, and then you can pull up on the connector right there. Just put the tool in there and that'll move the lock, or you can use your finger. Then we'll pull this hose. When we pull this hose off, the washer fluids going to go all over the place, so having a bucket underneath. Or if your system's empty, it's not going to matter.
Going to use a 90 degree pick. Stick it in underneath the hose, and just work it around a little bit. That'll break the seal, and I should be able to push it off. Pull that out of the way. Okay, so now that it's drained and pull out on the pump, just slightly. Pull it out, and then pull up. It's how you get the pump out.
To put the pump back in, you're going to put that Tam down in the grommet. Push and then push down all the way. Then push it, lock it in. Next we can take our hose and our wiring harness, slip it over here. Going to put the hose on the pump first. It's a little tricky to get in here, but push it on. Push it down onto the pump. Probably want to go a little bit further. That looks good right there. Push the hose in this groove here, and then we'll connect this electrical connector for the pump, and then push this wire into that groove. We're going to put this on. Keep in mind to keep this up. That little rubber piece. Going to line up those.
We're going to line these lock tabs with those holes. If you get it lined up top, you can push in the bottom and it should lock in. So we have these four 10-millimeter bolts that are going back in. These ones are going to go into the plastic, the ones that look more aggressive and the tighter threads. These will go right there. And then these little ones are going to go in the center into the metal frame. So we'll start all those first. Now we'll tighten these down with our 10-millimeter socket and extension and ratchet. Tighten it snug. And the last one. We're going to put this cover on. Get all the holes lined up for the pushpins. Push those in. Then, right there.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
How Where To Find Date of Manufacture On Your Vehicle
If you need to find the manufacture date of your vehicle, check this video out and learn where it might be located
